首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Laser cleaning was applied to remove aged and soiled oil paints of the 19th century from weathered, brittle sandstone surfaces. In contrast to other tested cleaning methods, the laser technique allows the removal of the oil paint layers with a minimum of material loss in brittle zones. The cleaned test areas have been investigated by optical and scanning electron microscopy as well as by colour measurements. The investigations have shown that the dirt and the oil paint layers can be removed by laser cleaning without affecting the original sandstone surface and that the pores can be opened again. The brown shade after cleaning is not caused by laser interaction with the sandstone surface but by historic impregnation with linseed oil. Immediately after cleaning, a treatment with chemical consolidants is necessary to preserve the brittle sandstone surface. Sustainable consolidation could be problematic in some areas, because the laser cleaning also preserves heavily damaged, crumbling zones of the carvings. For economic reasons, laser cleaning should be applied only in the most endangered zones of carvings and combined with classical methods (organic solvents and scalpel).  相似文献   

2.
A series of tests has been conducted to evaluate the potential for using a Q-switched Nd:YAG laser (wavelengths 1 064, 532 and 266 nm) to clean both new and naturally aged cotton textiles. Tests have been carried out on i) plain weave and velvet cotton and ii) new and naturally aged cotton samples to investigate the possible roles of weave structure and ageing in the cleaning process. Cleaning trials have been carried out on artificially soiled new cotton and compared with results obtained using traditional cleaning techniques: wet cleaning and organic solvent cleaning. Cleaned surfaces were examined using optical and scanning electron microscopy.  相似文献   

3.
On-line monitoring or even closed-loop control is necessary to avoid over-cleaning in case the ablation process is not self-limiting. Therefore, the laser-induced breakdown spectroscopy (LIBS) was used. Basic investigations were carried out on original sandstone samples (Elbsandstein) with strong encrustations as well as medieval stained glass samples (13th century from Cologne Cathedral). The spectroscopic study has shown that the plasma emission can be used for determination of the elemental composition of the ablated material. The plasma was initiated by 248-nm pulses of an KrF-excimer laser (30 ns FWHM). For the spectroscopic analysis, a grating spectrograph in combination with an optical multichannel analyser was used. For the glass and stone samples we obtained a continual alteration of the LIBS spectrum (vanishing of peaks and generating of new element peaks) during the removal process. Thus, certain element peaks can be used to distinguish between encrustation layer and valuable underlying material. To show the potential of LIBS we designed an experimental laser cleaning set-up including closed-loop LIBS control and demonstrated successful automatic cleaning of an original glass fragment.  相似文献   

4.
The development of laser cleaning as a conservation treatment has imposed a need for the evaluation and assessment of other cleaning techniques. The use of more traditional methods like abrasive cleaning, steam cleaning and chemical cleaning has relied so far on visual assessment, unlike much of the research applied to laser cleaning. A conscientious use of these cleaning methods requires their assessment as well as the need for a comparison based on a common methodology. A topographical assessment of laser cleaning, abrasive cleaning, steam cleaning and chemical cleaning (using hydrofluoric acid, ammonium carbonate and EDTA) is presented. Topographical variations induced on marble, oolitic limestone and architectural terracotta surfaces are assessed by means of light interferometry, showing the potential of this non-contact and non-destructive technique for surface studies in conservation. The comparison between cleaning treatments is based upon key parameters associated with cleaning surfaces. The aesthetic impact of these treatments is verified by means of optical microscopy and quantified by colour measurement. Chemical analysis of the cleaned surface (EDS) is performed to investigate the removal of surface pollutants and the presence of residues. Finally, petrographical analysis was used to investigate the removal of pollutant layers and its effect on surface texture.  相似文献   

5.
The utilization of laser light to produce fine and selective cleaning of superficial deposits and encrustation from stones was originally proposed more than 20 years ago by John Asmus who performed pioneering trials of laser cleaning on stone façades in Venice, Cremona and Padua. The opportunity to collect stone samples from these sites allowed us to carry out an original study aimed at evaluating the conservation state of stone surfaces cleaned 10–20 years ago by means of three different techniques: Nd:YAG laser radiation, micron sandblasting and chemical pads. Samples of various stone types, as Istria limestone, Botticino limestone and Nanto sandstone were collected and examined by means of optical and SEM microscopy, FT/IR, and EDAX analyses. The results provided preliminary indications that the state of conservation of stone surfaces previously subjected to laser cleaning is generally better in comparison with those which concurrently underwent mechanical and chemical cleaning.  相似文献   

6.
Lasers have served as cleaning tools for historical objects and artworks for about 40 years. In many cases, superior results of laser cleaning were achieved with respect to traditional methods. In this technique, contaminations on the surface of the object are ablated by laser irradiation. In order to apply laser cleaning method to fragile materials such as paper made of cellulose or parchment, heat deposition to the bulk should be minimal, to prevent damage. In this work, it is demonstrated that laser pulses with femtosecond (fs) duration can exhibit non-thermal ablation of contaminants on paper samples. In particular, laser cleaning studies are concentrated on paper samples with sizing. Fs laser cleaning is performed on artificially soiled and aged samples, as well as on historical ones. The laser used in the experiments has pulse duration of 550 fs and 1030 nm center wavelength. The fluence of the laser is varied and the post-cleaning statuses of samples are investigated. The analyses are color changes, fiber integrity, chemical composition changes and mechanical strengths. These results show that fs lasers can be very efficient in cleaning paper samples, yielding minimal discoloration and no damage to fibers distinguishable on microscopic examination. The presence of sizing also provides further protection against possible side effects.  相似文献   

7.
The hewn sandstone and ornamental figures of the Albertino Chancel, built around the mid-14th century, are covered with black encrustations of plaster and carbon deposits, often several millimetres thick. Their removal constitutes one of the main objectives in the conservation of the precious materials of the cathedral. The Nd:YAG laser method cleans the original surface of hardened encrustations without damaging or affecting the old coloured plasters and without affecting the centuries-old patina. Laser-Tech GmbH, founded by two expert restorers from Austria and Italy, is specialised in large-scale projects and, regarding the present project for the chancel, has managed to combine the sensitivity of the preserver with the laser technology applied to large surfaces. The present project concerning St. Stephen's Church comprises over 2000 m2 of stone surface treated only with laser systems, by groups of qualified restorers trained at Altech to use such instrumentation on artistic historic surfaces.  相似文献   

8.
The German Federal Foundation for the Environment (Deutsche Bundesstiftung Umwelt) is one of Europe's largest organizations of its kind. It supports innovative, exemplary projects for the protection of the environment and of national historic monuments and cultural landscapes. All projects are set up to provide a platform for researchers, craftsmen and restorers to find a common solution to difficult problems in conservation practice. More than 360 projects have been funded since 1990. Two recent projects deal with laser cleaning, one for stone and the other one for stained glass windows, the latter being presented here. This publication gives an overview on cleaning problems on stained glass windows and the project methodology. The interdisciplinary approach of the project provides the possibility of including experts in different fields to examine perspectives and limits of laser cleaning for stained glass windows. Two other publications in this issue (LACONA III) give selected results on cleaning experiments achieved within this project.  相似文献   

9.
In the framework of the preservation project of the Porta del Paradiso, carried on by the Opificio delle Pietre Dure of Florence, we investigated a cleaning methodology based on integrated chemical and laser techniques. This novel approach, which will replace the previous chemical protocol, was aimed at cleaning a number of gilded sculptural elements of the door frieze, without their being dismounted from the bronze framework. To such an end, optimised chemical and laser cleaning techniques were first singly investigated, and then integrated treatments were tested. The critical evaluation of each procedure was achieved through various diagnostic means to characterise the cleaned surfaces from chemical and physical points of view. The analysis demonstrated the various advantages of a laser-based treatment followed by light sodium potassium tartrate poultice application.  相似文献   

10.
The eligibility of laser cleaning is tested on regionally specific sculptural stones. Marlstone and sandstone represent the most common building, architectural and sculptural stones employed in the Czech Republic since the Romanesque period. These stone types differ greatly from the marbles on which positive results have been obtained using laser cleaning. Experimental samples were prepared by sawing rock cores. Artificial blackening of samples’ surfaces simulates natural black patinas. The experimental laser cleaning was conducted using Nd:YAG commercial laser (Laserblast 50) at two different fluences—the low one corresponds to the minimum operating capability of the equipment, and the high fluence represents the maximum operating mode of the equipment (i.e. in the ordinary operating range of the equipment). The samples were cleaned under dry and wet conditions. Use of a high fluence resulted in cratering/spalling that is discussed in terms of rock mineralogical composition (presence of clay minerals), adsorption of moisture on clay minerals and physical properties (porosity). Tensional fracturing (evidenced by scanning electron microscopy) along the cleaned surface is the main mechanism of sample destruction due to the vaporization of adsorbed moisture and due to the different elasticity of present rock-forming minerals. Observed discoloration due to high fluence and insufficient cleaning effect of low fluence present other problems encountered.  相似文献   

11.
Laser cleaning of ancient marble and stone monuments is nowadays a well-accepted procedure in conservation. Operators and specialists are presently divided between those giving maximum confidence to this method of cleaning and others who, in contrast, are strongly critical and emphasise possible drawbacks and damages caused by laser. As any other method of cleaning, laser also offers advantages but at the same time is limited by drawbacks. Most conveniently, it should be integrated with the other methods. On the basis of the above considerations, the authors are proposing a combined procedure using laser cleaning as a first step – in this way removing the relevant part of black gypsum encrustation – followed by chemical methods as a final step. The latter, conveniently, could be accomplished by means of anion exchange resins, better than ammonium carbonate. An experimental check-up was made of four different methods applied on three different lithotypes on the façade of the Florentine Cathedral. Laser, micro-sandblasting, ammonium carbonate and sodium EDTA were the cleaning methods compared, whilst Carrara marble, green Serpentine (Verde di Prato) and a red limestone were the three lithotypes. Results are commented by showing differences in the advantages and drawbacks among the different methods on the various lithotypes.  相似文献   

12.
The application of lasers for the removal of superficial deposits from historic stained glass is a comparatively new field of scientific interest. Experimental studies concerning the behaviour of glass substrates and the corresponding superficial deposits towards different laser wavelengths were carried out. The experiments were performed using wavelengths of λ = 193 nm (ArF-Excimer), 308 nm (XeCl-Excimer), 355 nm (Nd:YAG third harmonic) and 1 064 nm (Nd:YAG fundamental) in comparison to λ = 248 nm (KrF-Excimer). This comparison is due to the fact that the present knowledge is based on the 248 nm wavelength. Specially prepared model glass samples representing the original fragments and samples of organic polymers (formerly used as a protective material for historic stained glasses) were used to study the effects of laser radiation and were subsequently characterised by optical microscopy.  相似文献   

13.
A KrF-excimer laser operating at λ = 248 nm was used for basic studies in cleaning ancient glass surfaces. For irradiation a mask projection technique was applied. A modified optical set-up was designed using cylindrical lenses for large area removal by line scanning. Previous investigations revealed insufficient knowledge about interaction processes between UV-laser radiation and individual surface layers of encrusted historical glass. Thus, first detailed studies were carried out on special model glass samples simulating the behaviour of historical glass. The potential of removing crusts, bio layers as well as layers of different conservation materials (due to former conservation work) were examined. The avoidance of damaging material such as gel layers, paint layers or the bulk glass was of great importance. Removal rates and thresholds for the materials mentioned above were carried out. The collected data enables a comparison and evaluation of the feasibility for the removal of superficial layers from historical glass artefacts. The results indicate that in some cases a closed loop process control will be necessary to avoid over-cleaning.  相似文献   

14.
The study of the interaction between silica glass and saturated Ca(OH)2 solutions can be a useful approach to resolve the problem of the adhesion between lime-sand mortar and clay bricks. Since it is reasonable that the silica–calcium hydroxide system well simulates a brick–mortar system, experimental observations concerning the interaction of silica glass and this strong basic solution should be of value for the comprehension of the chemical reactions that could take place at the mortar–brick interface, maybe affecting the adhesion between the two building materials. We demonstrated the effects of saturated Ca(OH)2 solutions on commercial pure silica glass (fused silica) and on silica films obtained via a sol–gel process by means of dip-coating. Silica samples were dipped in the solutions at different temperatures (room temperature, 60 and 80 °C) and at different time intervals (1 and 21 h) and then they were analysed by means of surface techniques: X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM). It has been shown that Ca(OH)2 reacts with the silica glass network. The experimental results clearly show a very different behaviour of sol–gel silica with respect to fused silica, probably because of their different nanostructure. Many problems concerning the interaction of silica and Ca(OH)2 are still to be solved, but the results of this research strengthen the idea that adhesion between lime-sand mortar and clay bricks is caused not only by carbonation of calcium hydroxide contained in the mortar, but even by some chemical reactions involving the brick constituents and calcium hydroxide itself. The final products, calcium silicates, may induce a chemical continuity between lime-sand mortar and clay bricks.  相似文献   

15.
In the present work, an analytical characterization of painted plaster samples coming from ancient buildings dated back to 2nd cent. B.C., located in Licata (Sicily, Southern Italy), has been carried out. The investigation has been performed through different spectroscopic techniques: X-ray fluorescence (XRF) using an handheld energy-dispersive XRF analyzer, scanning electron microscopy equipped with an Energy Dispersive Spectrometry microanalysis detector (SEM-EDS) and Fourier transform infrared absorbance spectroscopy (FT-IR). The main goal is to identify the plaster and pigments material. In particular, the XRF investigation of surfaces is the first step for a preliminary elemental characterization. Then, through SEM-EDS measurements, a quantitative analysis of the chemical composition of the plaster and the pigmenting agents along with eventual components related to deterioration processes has been obtained. Finally, FT-IR absorbance spectra have proven to be a useful tool to investigate the molecular nature of the used materials.  相似文献   

16.
A polyfluorinated compound was studied as a material for the specific protection of calcarenite. Water capillary absorption and vapour permeability measurements were carried out in order to evaluate efficiency as a protective agent. Particular attention was given to characterising its resistance against bio-deterioration induced by microorganisms such as blue and green algae. Chemical surface modifications were induced by UV-irradiation in a specially designed climatic chamber and were investigated through comparative tests on untreated and artificially weathered samples using X-ray photoelectron spectroscopy (XPS). This paper discusses the potential use of the compound studied as a specific coating material for the protection of calcarenite.  相似文献   

17.
It is a common practice to use several chemical products during restoration projects of monuments or sculptures. However, care must be taken when combining the products to avoid a misuse. For example, it is well-known that applying a biocide on stone before a water-repellent leads to a diminishment of the hydrophobic effect of the treatment. But the application of biocide after a water-repellent treatment has been poorly analysed, although studies have proven that the stone looses its hydrophobicity after the application of the biocide. Henceforth, this study investigates the effects of biocide application on a water-repellent film and focuses on the possibilities to restore the efficiency of the previous water-repellent treatment (after the application of the biocide). At first, the tests were performed on glass slides to understand the mechanisms, with the subsequent results revealing that the biocide product deposits on the water-repellent film. Then, the study focuses on determining methods to remove the remains of biocide on limestone samples, previously treated with a water-repellent. The water-repellent used in the study is an alkylpolysiloxane, Rhodorsil H224 from Rhodia.  相似文献   

18.
This study presents characterizations of weathering forms of the same oolitic limestone from four quarries and eight monuments exposed on various environmental conditions focusing on the waterproofing effect of endolithic organic matter. Patinas were analyzed by X-ray diffraction (XRD), scanning electron microscopy with energy dispersive X-ray spectrometry (SEM-EDX), capillarity coefficient through weathered and unweathered sides, gypsum content and porous network morphology by epoxy resin molding. Study of weathering forms on old quarries indicates that lichens colonization (Verrucaria nigrescens and Caloplaca aurantia) can fill the superficial porous network with a dense network of lichenised fungal hyphae. Capillary coefficient measurement on natural and calcinated samples showed that endolithic organic matter can waterproof the stone and could act as a sulfate contamination barrier. Similar endolithic organic layer due to ancient lichens growth are found on some antique monuments of the Nîmes downtown and could explain their well-preserved state, unlike decayed 19th century churches that were never colonized by lichens.  相似文献   

19.
Most of the historical paints are mainly constituted by inorganic pigments, either pure or mixed, spread on the surfaces using different binding agents. The knowledge of the exact amount of different constituents of the paint, as well as of the mixing and pictorial techniques, is crucial for a careful program of conservation of polychrome works. Moreover, since the availability of these pigments has been changing through the centuries, their identification and chemical characterisation is useful to acquire or deepen information about the artist and his/her work. This information can also be useful for authentication purposes through relative dating because the identification of one pigment respect to another one can be used as a terminus post quem or ante quem the artwork was realized. In this work, X-ray fluorescence data from historical pigments, both pure and mixed, will be presented, in order to obtain quantitative information on the samples and to extract calibration curves to the aim of evaluating the pigment concentration in unknown mixtures.  相似文献   

20.
The chemical composition of 11 glass panes originating from two 13th century non-figurative windows were analyzed by means of Scanning Electron Microscopy–Energy Dispersive X-ray system (SEM-EDX). The windows were discovered in the back-wall of the triforium during the restoration of the choir of the cathedral St. Michael and St. Gudule in Brussels (Belgium). In order to determine if these windows were fabricated with glass of different origin or not, the compositional difference between the panes were compared with the variation in composition as a result of the following causes: (1) compositional fluctuation between panes cut from the same sheet of glass, (2) compositional fluctuation caused when panes are cut from different sheets that were made with the same batch, (3) compositional fluctuation caused when the glass is made from different batches at the same production center, and (4) compositional fluctuation as a result of glass produced at different fabrication centers.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号