共查询到20条相似文献，搜索用时 15 毫秒
1.
通过制作多组试件对污水污泥页岩实心砖的轴心抗压性能进行试验,并和烧结粘土砖相对比,得出了污水污泥页岩实心砖砌体的轴心抗压强度指标值均高于相同等级条件的粘土实心砖砌体的轴心抗压强度值,为污水污泥页岩砖的实际应用提供了依据. 相似文献
2.
建立了T形配钢型钢混凝土偏压构件力学性能分析的有限元模型,计算结果得到以往实验结果的验证。在此基础上,分析了不同阶段材料应力状态和各参数对偏压构件力学性能的影响。结果表明:T形配钢型钢混凝土构件在不同加载角下的性能有所不同,加载角为180°时极限承载力大于其他角度情况;混凝土抗压强度、型钢含钢率、配筋率、荷载偏心率、长细比对构件荷载-变形曲线的影响较大,随着混凝土强度、型钢含钢率、配筋率的增加,极限承载力和刚度增加;随着荷载偏心率的增加,极限承载力和刚度下降;随着构件长细比的增加,构件承载力总体呈现线性下降趋势,刚度下降明显。 相似文献
3.
In this study, nine simplified short composite columns consisting of core CFST (concrete filled steel tube) of different diameters and outer reinforced concrete were constructed to study their compressive performance under axial or eccentric compression. The failure mode is characterized by the crush of the outer concrete. The bearing capacity increases at first and then decreases with further increase of the position coefficient. It can be concluded that position coefficient is an important structural parameter that has considerable influences on the ultimate bearing capacity of the composite columns. The outer concrete, steel tubes and longitudinal reinforcement are found to work in a cooperative manner under axial or eccentric compression when the position coefficient is about 0.5. An improved bearing capacity algorithm that takes the position coefficient into account has been proposed based on the experimental and simulation results and current technical specification in China. It has been proven to be precise and safe. 相似文献
4.
Based on the characteristics of an L-shaped column composed of concrete-filled square steel tubes, the axial compression experiment and nonlinear finite element analysis were carried out to study the mechanical property of the L-shaped column. The load-displacement curve for the L-shaped column, the deflection and load-strain curves for the mono columns were obtained by the axial compression experiment. The results show that the L-shaped column exhibits a flexural-torsional buckling failure mode. The numerical simulation by the finite element analysis shows that the bearing capacity and failure mode are in accordance with those of the axial compression experiment and the feasi- bility of the finite element analysis is proved. For the calculation of the bearing capacity of the L-shaped column com- posed of concrete-filled square steel tubes, an analytical method is proposed based on the theory of the elastic stability and spatial truss model. The results of the analytical method are in good agreement with those of the axial compression experiment and the finite element analysis. 相似文献
5.
Ten slender steel reinforced cencrete (SRC) composite columns are tested under eccentric loading conditions.Effects of concrete strength, slenderness of columns and eccentricity of the axial load are studied. The load-carrying capacity is reduced with increased slenderness ratio and eccentricity. Concrete strength has no obvious influence on eccentrically loaded columns. Then, a nonlinear numerical method of pin-ended slender columns is also presented. This method is applicable for determining the material failure load or buckling failure load of a slender steel reinforced concrete composite column. In this method both material and geometric nonlinearities are taken into account. The results of numerical analysis accord well with the test results. The test results are also compared with the results predicted by ACI318-05 and the China Specifications. 相似文献
6.
Numerical Derivation of Strain Rate Effects on Material Properties of Masonry with Solid Clay Bricks
In this paper, numerical method is used to study the strain rate effect on masonry materials. A typical unit of masonry is selected to serve as a representative volume element (RVE). Numerical model of RVE is established with detailed distinctive modeling of brick and mortar with their respective dynamic material properties obtained from laboratory tests. The behavior of brick and mortar are characterized by a dynamic damage model that accounts for rate-sensitive and pressuredependent properties of masonry materials. Dynamic loads of different loading rates are applied to RVE. The equivalent homogenized uniaxial compressive strength, threshold strain and elastic modulus in three directions of the masonry are derived from the simulated responses of the RVE. The strain rate effect on the masonry material with clay brick and mortar, such as the dynamic increase factor (DIF) of the ultimate strength and elastic modulus as a function of strain rate are derived from the numerical results. 相似文献
7.
To investigate the seismic behavior of autoclaved aerated concrete load-bearing masonry wall（AACLMW）, a piece of control block wall without constructional measures and five pieces of block walls with different constructional measures were tested under low reversed cyclic loading which imitated low to moderate earthquake force. The seismic behavior of AACLMW with different constructional measures in terms of failure mode, hysteretic curve, deformation capacity and displacement ductility was studied and compared with that without constructional measures. The experimental results indicate that the constructional measures comprising constructional columns and horizontal concrete strips are effective for improving the seismic behavior of AACLMW. The study in this paper can provide a reliable experimental basis for further analysis and engineering application of AACLMW in the future. 相似文献
8.
根据内置CFRP圆管的方钢管高强混凝土的特点,通过引入混凝土强度折减系数和等效约束折减系数,将内置CFRP圆管的方钢管高强混凝土等效为内置CFRP圆管的圆钢管高强混凝土。进而,在统一强度理论的基础上,推导出内置CFRP圆管的方钢管高强混凝土轴压构件的强度承载力。通过引入整体稳定系数,推导出内置CFRP圆管的方钢管高强混凝土轴压中长柱的稳定极限承载力公式。将该公式的计算结果与试验结果进行了比较,结果表明该理论公式是正确可行的。理论公式以期能为工程应用提供帮助。 相似文献
9.
基于 8个碳纤维布约束高强混凝土棱柱体试件的试验 ,研究了碳纤维布对提高高强混凝土抗压强度和改善其变形性能的作用 .试验发现 ,包裹碳纤维布可以提高试件的抗压强度 ,并有效地改善混凝土的变形性能 ,其效果随碳纤维用量的增加而更加显著 .在试验基础上 ,根据理论分析和对试验结果的整理 ,归纳出碳纤维布约束高强混凝土的应力 应变全曲线方程 .最后 ,利用提出的全曲线方程编制计算机程序 ,分析了包裹碳纤维布对提高高强混凝土压弯构件的强度和延性的作用 相似文献
10.
11.
《天津大学学报(英文版)》2015,(3)
In order to improve the seismic performance, deformation ability and ultimate load-carrying capacity of columns with rectangular cross section, engineered cementitious composite(ECC) is introduced to partially substitute concrete in the edge zone of reinforced concrete columns and form reinforced ECC/concrete composite columns.Firstly, based on the assumption of plane remaining plane and the simplified constitutive models, the calculation method of the load-carrying capacity of reinforced ECC/concrete columns is proposed. The stress and strain distributions and crack propagation of the composite columns in different states of eccentric compressive loading are analyzed. Then, nonlinear finite element analysis is conducted to study the mechanical performance of reinforced ECC/concrete composite columns with rectangular cross section. It is found that the simulation results are in good agreement with the theoretical results, indicating that the proposed method for calculating the load-carrying capacity of concrete/ECC composite columns is valid. Finally, based on the proposed method, the effects of ECC thickness, compressive strength of concrete and longitudinal reinforcement ratio on the mechanical performance of reinforced ECC/ concrete composite columns are analyzed. Calculation results indicate that increasing the thickness of ECC layer or longitudinal reinforcement ratio can effectively increase the ultimate load-carrying capacity of the composite column with both small and large eccentricity, but increasing the strength of concrete can only increase the ultimate loadcarrying capacity of the composite column with small eccentricity. 相似文献
12.
In this study, an artificial neural network （ANN） model for studying the strength properties of steel fiber reinforced concrete （SFRC） containing fly ash was devised. The mixtures were prepared with 0 wt%, 15 wt%, and 30 wt% of fly ash, at 0 vol.%, 0.5 vol.%, 1.0 vol.% and 1.5 vol.% of fiber, respectively. After being cured under the standard conditions for 7, 28, 90 and 365 d, the specimens of each mixture were tested to determine the corresponding compressive and flexural strengths. The pa- rameters such as the amounts of cement, fly ash replacement, sand, gravel, steel fiber, and the age of samples were selected as input variables, while the compressive and flexural strengths of the concrete were chosen as the output variables. The back propagation learning algorithm with three different variants, namely the Levenberg-Marquardt （LM）, scaled conjugate gradient （SCG） and Fletcher-Powell conjugate gradient （CGF） algorithms were used in the network so that the best approach can be found. The results obtained from the model and the experiments were compared, and it was found that the suitable algorithm is the LM algorithm. Furthermore, the analysis of variance （ANOVA） method was used to determine how importantly the experimental parameters affect the strength of these mixtures. 相似文献
13.
彭燕 《杨凌职业技术学院学报》2014,(1):10-12
采用ANSYS软件进行了数值模拟,分别对比了三种型钢截面形式和i种轴压比对型钢高强混凝土柱的延性和耗能性能的影响。从计算结果可以看出,轴压比越小,延性系数越大,抗震性能越好;带翼缘十字形型钢柱的延性比不带翼缘十字形型钢柱的延性好。 相似文献
14.
Chromatograms of tocopherol homologues were obtained by a column of analytical size （inner diameter （ID） 0.46 cm cm×10 cm） packed with silica gel. Adsorption isotherms and film mass-transfer coefficient were estimated from the chromatograms by using a general rate model, which considers axial dispersion, external mass-transfer and intraparticle diffusion. Based on the obtained isotherms and mass-transfer coefficient, the separation process of tocopherol homologues on simulated moving bed （SMB） was simulated using the same model. According to the simulated results, a mixture of α-, γ-, δ-tocopherols and other impurities was separated on an SMB equipment. The SMB equipment was composed of 8 columns of ID 2 cm× 1 0 cm, with 2 columns in each section. The solid phase was silica gel, and the mobile phase was n-hexane/2-propanol （99/1 by volume）. γ- and δ-tocopherols of purity greater than 98% were obtained with recovery greater than 98%. The effects of operating conditions （flow rates and switching time） on the performance of SMB were studied by both simulation and experiments. It was found that all the simulation results were quite close to the experimental results. We conclude that process development and optimization of operating conditions of SMB by simulation are feasible. 相似文献
15.
建筑砖砌体裂缝种类繁多,形态各异.较轻微者影响建筑物美观,造成渗漏水;严重者降低建筑结构的承载力、刚度、稳定性、整体性、耐久性,甚至还有导致建筑物整体倒塌的可能性.因此,正确分析原因、切实加以防治十分必要,十分迫切. 相似文献
16.
通过对粉煤灰的硫酸改性得到酸改性粉煤灰,用其对含铅模拟废水进行吸附实验,探讨改性的最佳条件,并在最佳改性条件下制得改性粉煤灰,研究改性粉煤灰投加量、吸附时间、吸附温度以及pH值对Pb2＋吸附效果的影响.结果表明,在投加量为10 g/L,吸附时间为50 min,吸附温度为50℃,pH-6时,改性粉煤灰对40 μg/mL的Pb2＋的去除率可达90.34％,能够较好的去除废水中的Pb2＋. 相似文献
17.
因为异形柱经常承受偏心受压加受扭的复杂受力,所以理论计算比较复杂。本研究使用有限元分析软件ABAQUS对T形截面型钢混凝土柱的抗扭性能进行了数值模拟分析,并考虑混凝土塑性发展探讨不同轴压比与钢骨率对型钢混凝土T形截面柱延性与抗扭承载力的影响。利用已有的实验数据,建立构件的受压有限元模型,通过对比荷载-位移曲线验证有限元材料本构的有效性。建立三组模型分析不同轴压比与钢骨率对构件抗扭力学性能的影响,为今后型钢混凝土异形柱的应用提供参考。 相似文献
18.
以硅酸盐和硫铝酸盐复合水泥为基材制作水泥基注浆材料,分别讨论了不同类型、不同掺量的粉煤灰和矿粉对水泥基注浆材料的流动度、容重、膨胀率、抗压抗折强度的影响。结果表明:粉煤灰能有效地增加水泥基注浆料的流动度,当粉煤灰掺量低于20%时,可以提高注浆料的塑性膨胀率,当Ⅰ级粉煤灰掺量为20%或Ⅱ级粉煤灰掺量为15%时,3 h膨胀率最高达1%;粉煤灰对注浆料的早期强度不利,但可以增强其后期强度。矿粉可以改善其流动度,随着矿粉的增加,注浆料的容重和膨胀率均呈下降趋势;矿粉对注浆料的28 d强度无显著影响,其早期强度随着矿粉的增加而下降,当S75矿粉掺量高于7%或S95矿粉掺量高于11%时,抗压抗折强度不满足规范要求。 相似文献
19.
20.
黄玉宁郑永乾赖鹏松 《福建工程学院学报》2020,(4):329-335
采用有限元软件ABAQUS建立了不同加载角T形带肋和多室钢管混凝土压弯构件的计算模型,数值计算结果与试验结果吻合良好。对影响T形钢管混凝土柱水平荷载P-水平位移Δ关系曲线的参数进行分析,结果表明:加载角为0°时,T形钢管混凝土构件的承载力最低,在67.5°负向加载时,构件的承载力最大,比0°加载角构件大13%左右,加载角为45°~90°间承载力总体上差别不大。随着钢管屈服强度、混凝土抗压强度、钢管长厚比、带肋和多室T形钢管混凝土构件在斜向加载的承载力增加,在传统钢管混凝土基础上,提出了适用于不同加载角带肋和多室T形钢管混凝土压弯构件的承载力设计方法,简化计算公式与有限元结果、试验结果均吻合较好。 相似文献