首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 536 毫秒
1.
基于R290冷媒旋转式压缩机,对低油量技术的应用进行了研究,以帮助R290空调系统满足标准的制冷剂充注量限制要求。首先,根据R290制冷剂的应用要求,明确了R290压缩机的设计要点,提出了低油量压缩机的设计思路。其次,根据旋转式压缩机的供油要求设计了低油量旋转式压缩机的结构,完成了供油能力CFD计算分析。再次,完成了低油量压缩机与普通压缩机的供油能力评价,并对比分析了压缩机的性能和耐久磨耗试验结果。最后,在同一套空调系统中,完成了系统性能和R290充注量对比试验,分析了R290低油量压缩机为空调系统带来的效果。研究结果表明,低油量旋转式压缩机可有效减少系统制冷剂充注量,并能保证压缩机及系统的性能和可靠性,具有良好的应用前景。  相似文献   

2.
文章旨在研究制冷系统中R454B相较于R410A的可替代性,对比分析了R454B和R410A在制冷系统中所表现出的制冷量、压缩机功耗、系统COP和排气温度。通过实验得出蒸发器/冷凝器出水温度分别与蒸发温度、冷凝温度呈正相关,且实验变量对性能参数的影响具有相似性;制冷量和系统COP均随蒸发温度的升高、冷凝温度的降低而增大,而工质物性对系统COP的影响并不大;压缩机功耗和排气温度随蒸发温度的降低、冷凝温度的升高而增大。  相似文献   

3.
针对非共沸环保混合制冷剂(R744/R717)自然复叠制冷-40℃冷柜模拟研究结果,在进一步探讨了该系统的变工况特性的基础上,提出应对冷却介质温度发生变化的系统控制方案及应对压缩机过热的系统改进方案.  相似文献   

4.
针对R290制冷剂应用的特点,重点分析了R290压缩机润滑油的选择过程中溶解度及溶解粘度的影响。指出了在R290制冷剂应用时,因排气温度低带来的过热度问题及其影响,提出了改善R290系统过热度问题的方法。  相似文献   

5.
压缩机是家用空调器的核心电气部件,压缩机一旦出现故障就意味着整个制冷系统处于不正常工作,在维修制冷系统的过程中。有效地解决制冷系统因压缩机导致的不正常工作是维修人员一定要掌握的维修技能。  相似文献   

6.
螺杆压缩机是我国石油化工企业的主要气体压缩设备之一,其运行状态直接影响整个压缩机组的安全性、可靠性及生产效率。螺杆压缩机一旦发生故障,将极有可能引起整套设备甚至整条生产线的瘫痪,严重降低生产效率并带来巨大的经济损失。选取71泵房螺杆压缩机的常见振动故障进行分析,并针对压缩机非正常停车问题,联系实际状况提出解决方案。  相似文献   

7.
R12对大气臭氧层有强烈的腐蚀作用.而R134a是一种新型的环保制冷剂,为减少环境污染,可用R134a代换R12.根据对R134a和R12特性的对比分析,改进了空调压缩机、冷凝器、蒸发器、膨胀阀和其他附属部件的具体结构及参数设置,汽车空调制冷系统可得到优化.  相似文献   

8.
为深入了解HFC125跨临界循环热泵热水器的运行特性,设计和建造了一个直流变频热泵热水器实验装置,对HFC125跨临界循环热泵热水器性能进行了实验研究,发现压缩机运行在95Hz时系统存在一个COP峰值.然后以95Hz为例,研究了系统COP与压缩机频率、冷凝压力、蒸发压力、冷却水温升、压缩机排气温度等参数的关系,并与R410A亚临界循环系统性能进行了比较.结果表明:系统存在一最优频率,此时系统有较好的COP值,系统COP随冷凝压力和压比的降低呈上升趋势,而蒸发压力基本恒定;当冷却水温升超过47.5℃时,COP迅速下降.相对R410A亚临界循环,HFC125跨临界循环系统COP显著提升,提高幅度平均在12%以上.  相似文献   

9.
针对氨水吸收/压缩复合制冷循环的方式不同,结合Schulz氨水溶液状态方程,分别对压缩机处于系统高压区和低压区2种不同的组合方式进行了理论分析计算.分析了在给定中间压力下,蒸发温度Te、热源温度Th和冷却水温度Tw对2种组合方式下压缩机当量热耗量qCW、热源耗热量qG和循环性能系数COP的影响.结果表明:压缩机当量热耗量对循环性能系数的影响要低于热源耗热量的影响;压缩机处于系统高压区时循环的一次用能量要明显高于压缩机处于系统的低压区;压缩机处于系统低压区时循环性能要优于压缩机处于系统的高压区.当中间压力给定时,存在一个最佳热源温度,使得氨水吸收/压缩复合制冷循环的性能系数取得最大值.  相似文献   

10.
针对使用R134a/R23混合制冷剂的自然复叠制冷系统.编制了基于NISTREFPROP的仿真程序。利用仿真和实验对系统各种优化措施的效果进行了分析和验证。两者都表明:分凝措施有利于降低系统蒸发温度、提高COP;而回热可以略微降低系统蒸发温度,但使系统COP降低、压缩机排气温度升高。  相似文献   

11.
采用表面修饰技术和添加分散剂的方法制备了均匀而稳定的R600a-纳米铝纳米流体,将其充注到半导体冰箱散热热管中以提高热管散热性能,采用红外热像仪研究了热管温度分布,利用冰箱性能试验室测试了半导体冰箱整机性能。试验表明以R600a-纳米铝为工质的热管散热性能优于普通热管散热性能,并分析了纳米流体提高热管散热性能的原因。  相似文献   

12.
建立双级内可逆卡诺制冷机模型,应用有限时间热力学理论,导出制冷系数与制冷率间的基本优化关系,给出其生态学优化性能,得到一些新的性能参数,并作些有意义的讨论,所得结论可供制冷机的最佳工作状态选择和优化设计提供新理论指导。  相似文献   

13.
以PLC为控制核心,对冰箱置物架生产系统进行了技术改进设计。分析了现有的冰箱置物架生产系统的缺点,着重介绍了冰箱置物架生产控制系统的硬件、软件设计方案。采用旋转编码器作为反馈器件,引入步进电机的局部闭环控制。  相似文献   

14.
This paper proposes a new approach to the performance optimization of an auto-cascade refrigerator (ACR) operating with a rectifying column and six types of binary refrigerants (R23/R134a, R23/R227ea, R23/R236fa, R170/R290, R170/R600a, and R170/R600) at a temperature level of −60 °C. Half of the six binary refrigerants are nonflammable, of which the 0.5 and the 0.6 mole fractions of R23 for the R23/R236fa possess the most prospective composition for the medium and low suction pressure compressors, respectively. The remaining three binary refrigerants are flammable but with low global warming potentials, of which the 0.6 mole fraction of R170 for the R170/R600 is the most prospective one. The results show that the overall matching as well as local matching of heat capacity rates of hot and cold refrigerants in the recuperators are important for the improvement of coefficient of performance of the cycle, which can be adjusted through the simultaneous optimization of the pressure level and composition. The new approach proposed also offers a wider range of applications to the optimization in performance of the cycle using multi-component refrigerants.  相似文献   

15.
介绍了冰箱制冷系统综合模拟实验装置的研制背景、组成、工作原理及应用情况。实验内容设计为开放式、研究型,因而通过本实验装置,学生不仅可以巩固冰箱制冷系统的基本原理、流程、结构,而且对冰箱系统常见的故障可以较为熟练地排除,提高学生的工程实践和动手能力,更有利于培养学生的综合实践能力、创新思维意识和创新思维能力。  相似文献   

16.
分析了制冷与空调专业推行CBE理论教学的基本条件,提出了CBE理论框架下的制冷与空调专业教学体系。教学实践表明,明确的专业培养目标、教评分开的职业能力评估体系和6:4的理论学时与实践学时的比例,是取得制冷与空调专业教学成功的重要保证。  相似文献   

17.
The optimization of the performance of a single-stage Linde-Hampson refrigerator (LHR) operating with six different binary refrigerants (R23/R134a, R23/R227ea, R23/R236ea, R170/R290, R170/R600a and R170/R600) with ozone depletion potentials (ODPs) of zero was conducted using a new approach at the temperature level of-60℃. Among these binary refrig- erants, the 0.55 and the 0.6 mole fractions of R23 for R23/R236ea are the most prospective nonflammable ones for the medium and low suction pressure compressors, respectively. For these two kinds of compressors, the 0.6 and the 0.65 mole fractions of R170 for R 170/R600, respectively, are the most prospective binary refrigerants with low global warming potentials (GWPs). The results of optimization of pressure levels indicate that the optimum low pressure value for coefficients of performance (COP) is achieved when the minimum temperature differences occur at both the hot and the cold ends of the recuperator at a specified composition and pressure ratio. Two useful new parameters, the entropy production per unit heat recuperated and the ratio of heat recuperating capacity to the power consumption of the compression, were introduced to analyze the exergy loss ratio in the recuperator. The new approach employed in this paper also suggests a promising application even to the optimization of the performance with multi-component refrigerants.  相似文献   

18.
The optimization of the performance of a single-stage Linde-Hampson refrigerator (LHR) operating with six different binary refrigerants (R23/RI34a, R23/R227ea, R23/R236ea, R170/R290, RI70/R600a and R170/R600) with ozone depletion potentials (ODPs) of zero was conducted using a new approach at the temperature level of-60 ℃. Among these binary refrig-erants, the 0.55 and the 0.6 mole fractions of R23 for R23/R236ea are the most prospective nonflammable ones for the medium and low suction pressure compressors, respectively. For these two kinds of compressors, the 0.6 and the 0.65 mole fractions of R170 for R170/R600, respectively, are the most prospective binary refrigerants with low global wanning potentials (GWPs). The results of optimization of pressure levels indicate that the optimum low pressure value for coefficients of performance (COP) is achieved when the minimum temperature differences occur at both the hot and the cold ends of the recuperator at a specified composition and pressure ratio. Two useful new parameters, the entropy production per unit heat recuperated and the ratio of heat recuperating capacity to the power consumption of the compression, were introduced to analyze the exergy loss ratio in the recuperator. The new approach employed in this paper also suggests a promising application even to the optimization of the performance with multi-component refrigerants.  相似文献   

19.
从制冷系统、提高箱体与门的绝热性能及电子技术控制三方面论述了提高家用冰箱能源使用效率的技术、方法 ,指出了节能冰箱是世界家电的发展方向  相似文献   

20.
由于禁止使用CFC—11,所以原有的聚氨酯发泡系统必须被替代,但是对于冰箱和冷柜隔热用聚氨酯系统的选择涉及诸多因素,因此并不是一个简单的过程。本文阐述了卤化物发泡剂和碳氢化合物发泡剂的特性以及它们的发泡体系的物理性能,根据各种发泡体系的综合比较,环戊烷/异戊烷混合发泡体系是较理想的替代方案,目前众多冰箱、冰柜厂家已部分采用这种发泡体系,江苏白雪电器股份有限公司也将选用这一发泡体系。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号