共查询到20条相似文献，搜索用时 31 毫秒
1.
退化钢筋混凝土桥梁概率耐久性评估方法 总被引：1，自引：0，他引：1
提出了考虑时间、空间变异特性的退化钢筋混凝土桥梁耐久性概率评估的随机有限元方法.首先,通过考虑钢筋与混凝土之间时变的粘结滑移关系及腐蚀钢筋的应力应变关系,采用弥散裂纹方法对退化钢筋混凝土桥梁进行有限元分析.然后,提出了退化钢筋混凝土桥梁耐久性概率评估的随机有限元分析方法,基于文献及现场调查的数据,采用蒙特卡罗仿真方法对... 相似文献
2.
研究了循环荷载作用下铝合金轴压构件的力学性能,并与钢轴压构件进行比较。采用通用有限元分析软件ANSYS对铝合金轴压构件的滞回性能进行有限元分析。分析方法考虑了材料非线性、几何非线性和初始缺陷的影响。根据计算结果,得到了6061-T6铝合金、6061-T4铝合金和Q235钢3种材料轴压构件的滞回曲线、恢复力骨架曲线和刚度退化曲线,并进行了比较研究。分析结果显示,铝合金轴压构件的滞回性能与低碳钢轴压构件较为类似,并受到材料本构关系的显著影响。 相似文献
3.
采用ABAQUS有限元软件对各种强度等级下各龄期钢筋混凝土梁的受扭性能进行分析。各龄期混凝土的本构关系采用塑性损伤模型,受拉指标采用断裂能。有限元分析结果表明:各龄期混凝土的抗扭承载力随龄期的增长而增长,开裂前早龄期混凝土梁的抗扭承载力主要由混凝土承担,钢筋的贡献很小;前3d是混凝土扭矩增长最快的主要时间段,开裂扭矩和极限扭矩达到28 d的60%左右。最后,根据有限元参数分析结果,在现行规范的基础上提出了早龄期混凝土梁开裂扭矩和极限扭矩的修正公式。 相似文献
4.
因为异形柱经常承受偏心受压加受扭的复杂受力,所以理论计算比较复杂。本研究使用有限元分析软件ABAQUS对T形截面型钢混凝土柱的抗扭性能进行了数值模拟分析,并考虑混凝土塑性发展探讨不同轴压比与钢骨率对型钢混凝土T形截面柱延性与抗扭承载力的影响。利用已有的实验数据,建立构件的受压有限元模型,通过对比荷载-位移曲线验证有限元材料本构的有效性。建立三组模型分析不同轴压比与钢骨率对构件抗扭力学性能的影响,为今后型钢混凝土异形柱的应用提供参考。 相似文献
5.
A study of the behaviour of constructional cold-formed stainless steel beams at elevated temperatures was conducted in this paper. An accurate finite element model （FEM） for stainless steel beams was developed using the finite element program ABAQUS. Stainless steel beams having different cross-sections were simulated in this study. The nonlinear FEM was verified against the experimental results. Generally, the developed FEM could accurately simulate the stainless steel beams. Based on the high temperature stainless steel material test results, a parametric study was carried out on stainless steel beams at elevated temperatures using the verified FEM. Both high strength stainless steel EN 1.4462 and normal strength stainless steel EN 1.4301 were considered. A total of 42 stainless steel beams were simulated in the parametric study. The effect of temperatures on the behaviour of stainless steel beams was investigated. In addition, a limiting temperature for stainless steel beams was also proposed. 相似文献
6.
为了研究钢筋增强ECC梁受弯性能,进行了钢筋增强ECC梁和普通钢筋混凝土梁受弯的对比研究.结果表明,相比普通钢筋混凝土梁,钢筋增强ECC梁的受弯承载力和延性分别提高了24.8%和187.76%,并且在梁中用ECC代替混凝土可有效延缓裂缝的发展.此外,采用简化的ECC本构模型对钢筋增强ECC及混凝土梁的受弯性能进行了非线性有限元分析,模拟结果与试验结果吻合较好,在服役期间钢筋增强ECC梁的裂缝可以控制在0.4 mm以下.ECC材料的使用可明显提高梁的抗弯承载力、变形能力、延性等受弯性能. 相似文献
7.
简要说明了研究锈蚀钢筋混凝土构件结构性能的意义，阐述了锈蚀钢筋混凝土构件结构性能的研究状况．主要从混凝土构件中锈蚀钢筋的力学性能、锈蚀钢筋与混凝土间粘结性能和构件的承载能力等方面总结归纳了国内外的研究现状与成果。 相似文献
8.
建立了T形配钢型钢混凝土偏压构件力学性能分析的有限元模型,计算结果得到以往实验结果的验证。在此基础上,分析了不同阶段材料应力状态和各参数对偏压构件力学性能的影响。结果表明:T形配钢型钢混凝土构件在不同加载角下的性能有所不同,加载角为180°时极限承载力大于其他角度情况;混凝土抗压强度、型钢含钢率、配筋率、荷载偏心率、长细比对构件荷载-变形曲线的影响较大,随着混凝土强度、型钢含钢率、配筋率的增加,极限承载力和刚度增加;随着荷载偏心率的增加,极限承载力和刚度下降;随着构件长细比的增加,构件承载力总体呈现线性下降趋势,刚度下降明显。 相似文献
9.
冯依锋 《襄樊职业技术学院学报》2011,10(5):22-24
国内外学者一直致力于研究钢筋与混凝土的粘结滑移本构关系,试图得到比较一致的结论,但由于钢筋与混凝土间传力机理复杂、影响因素多,目前尚无可以通用的公式。文章就普通钢筋混凝土和锈蚀后的钢筋混凝土两种情况下的粘结滑移本构关系的研究现状进行了阐述。 相似文献
10.
冯依锋 《襄樊职业技术学院学报》2013,(3):26-28
详细介绍了钢筋内贴片中心拔出试件的制作方法。中心拔出试验是研究钢筋与混凝土间粘结性能的有效方法,通过钢筋内贴应变片可以测得锚固区内不同位置的钢筋应力,进而揭示钢筋与混凝土的粘结特点。 相似文献
11.
HAO Qing-duo WANG Yan-lei ZHANG Zhi-chun OU Jin-ping 《浙江大学学报(A卷英文版)》2007,8(9):1356-1365
Based on the Canadian Standards Association (CSA) criteria,105 pullout specimens were tested to investigate the effect of different rib geometries on bond strength of glass fiber reinforced polymer (GFRP) rebars embedded in concrete. Two kinds of conventional reinforcing rebars were also studied for comparison. Each rebar was embedded in a 150 mm concrete cube,with the embedded length being four times the rebar diameter. The experimental parameters were the rebar type,rebar component,rebar diameter,rebar surface texture,rib height,rib spacing and rib width. Theoretical analysis was also carried out to explain the experimental phenomena and results. The experimental and theoretical results indicated that the bond strength of GFRP rebars was about 13%～35% lower than that of steel rebars. The bond strength and bond-slip behavior of the specially machined rebars varied with the rebar type,rebar diameter,rebar surface texture,rib height,rib spacing and rib width. Using the results,design recom-mendations were made concerning optimum rib geometries of GFRP ribbed rebars with superior bond-slip characteristics,which concluded that the optimal rib spacing of ribbed rebars is the same as the rebar diameter,and that the optimal rib height is 6% of the rebar diameter. 相似文献
12.
U型钢筋混凝土地道桥的受力计算比较复杂,涉及到挡土墙土压力计算的水土分算和水土合算,本文通过大型有限元软件ANSYS,建立U型钢筋混凝土地道桥的有限元模型和力学模型,对其进行三维有限元荷载应力分析。 相似文献
13.
杨晓静凌静秀银光球 《福建工程学院学报》2017,(1):30-34
基于虚拟样机技术及有限元法,提出了破碎站钢结构的力学模型等效及落料冲击系数的数值模拟方法,采用理论公式对单块物料冲击钢结构的动载系数进行计算,并将其与数值模拟分析结果对比。分析表明,1m3大小的正方体煤岩物料从5m高度下落直接冲击钢结构,其冲击系数的理论计算及刚体动力学分析结果均为123,而柔体动力学分析结果为125,三者误差约1.6%,表明提出的数值模拟方法及钢结构等效模型有效,分析方法可为破碎站的性能评估及结构优化提供基础。 相似文献
14.
Retrofitting of RC Slabs Against Explosive Loads 总被引：1，自引：0，他引：1
OEHLERS Deric John 《天津大学学报(英文版)》2006,12(Z1)
With the increase of terrorist bomb attacks on buildings, there is a need to develop advanced retrofitting techniques to strengthen structures against blast loads. Currently, several guidelines including an Australian version for retrofitting reinforced concrete (RC) structures are available for the design of retrofitting systems against seismic and monotonic loads using steel or fibre reinforced polymer (FRP) plates that can be either adhesively bonded to the surface or near surface mounted to the concrete cover. However, none of these guidelines provide advice suitable for retrofitting structures subjected to blast loads. In this paper, numerical models are used to simulate the performance of retrofitted RC slabs subjected to blast loads. Airblast pressure distributions on the surface of the slabs estimated in a previous study are used as input in the analysis. A material damage model developed previously for concrete and an elastoplastic model for steel bars are employed in this research for modelling reinforced concrete behaviour due to explosive loads. The material models and blast loading are coded into a finite element computer program LS-DYNA3D to do the analysis. With the numerical model, parametric studies are conducted to investigate RC slabs retrofitted by either externally bonded or near-surface mounted plates or GFRP sheets subjected to blast loads. Discussion is made on the effectiveness of the retrofitting system for RC slabs against blast loads. 相似文献
15.
16.
孙翠兰 《河北工业大学成人教育学院学报》2007,22(4):49-52,62
轻钢骨混凝土结构是一种新型的结构体系,它自重轻,安装方便,保温性能好,因而有广阔的发展余地和使用空间。本文分别对轻钢骨模网混凝土的工作性能、轻钢骨剪力墙的抗剪性能做了深入的理论研究。用3片缩尺轻钢骨剪力墙模型进行了试验研究,并推导了轻钢骨剪力墙的抗剪承载力公式。由于模型试验构件少,数据有所不足,本文又采用ADINA有限元分析软件进行分析,提出有关轻钢骨砼剪力墙轴压比设计的建议。 相似文献
17.
In order to research the bond properties between corroded reinforcement bars and concrete, reinforcement bars with different diameters and different types and concrete with different strength levels were treated specially with all soaking and impressed current method, and the bond properties were measured with the pull-out test. The comparative analysis of the bond properties of corroded reinforcement bars was carried out. The results showed that the types of reinforcement bars and concrete had great influence on the bond strength. The corrosion and volume expansion of reinforcement bars made concrete in tensile condition, which tended to produce cracks in parallel reinforced direction. The typical bond failure of plain reinforcement bars was pull-out, while the typical bond failure of ribbed reinforcement bars was split. The bond strength between corroded reinforcement bars and concrete increased with the increase of concrete strength. The bond strength of plain and ribbed reinforcement bars showed a decreasing trend after the first increase with the increase of the extent of corrosion. Through the test, the coefficients of the bond strength of plain and ribbed reinforcement bars were given, respectively. 相似文献
18.
Time-to-cracking of the concrete cover induced by the steel corrosion is one of the critical problems faced by engineers, operators and asset managers in making strategies for the maintenance and repairs of reinforced concrete (RC)structures affected by corrosion. In this paper, a theoretical model for predicting the time-to-cracking is derived by assuming the bond between the steel bar and the concrete as a linear combination of perfectly smooth and bonded. The model takes into account the characteristics of existing exiguous flaws and initial cracks in the concrete before the load acting on RC structures. The validity of the proposed model is preliminarily verified by comparing the obtained results with the available experimental results. A remarkable advantage of the proposed method is its application to the prediction of the service life of RC structures, made of the deformed steel bars as well as the round bars. By determining an experimental constant α, which is related to the interface bond state between the steel bar and the concrete, the service life of RC structures can be predicted using the proposed scheme. Analysis of major factors affecting the time-to-cracking demonstrates that the length of the initial crack affects the service life of RC structures significantly. Moreover, the larger cover thickness and the smaller diameter of the steel bar within a certain range are beneficial to prolonging the time-to-cracking. 相似文献
19.
A European pressurized reactor (EPR) steel containment liner structure is comprised of the cylinder part and the dome part. An introduction of the steel liner structure is presented, followed by studies on the key mechanical features of the construction process using a refined finite element method. The steel liner was divided into several modules and then assembled during construction. Firstly, the equipment structure used to hoist the liner module was optimized, the lifting lug was analyzed using a multi-scale finite element model; the wind speed limit during lifting was also studied. Subsequently, the effect of internal forces during assembly between the liner modules, the lateral pressure of fresh concrete, the non-uniform temperature load, and the wind load on the cylinder module was analyzed. According to the time-varying structural performance during continuous concrete pouring and the hardening construction, an “overlapping element and birth-death element” technique was adopted to analyze the deformation and stress of the long-span steel dome liner. In addition, the stability-bearing capacities of the dome structure during construction were also studied, which took into consideration the effect of the initial geometrical imperfections and the elasto-plasticity of the material. This study presents a reference in terms of the mechanics of the construction scheme and the safety of such a type of structure. 相似文献
20.
The earthquake-resistant property of reinforced concrete members depends on the interaction between reinforcing bars and surrounding concrete through bond to a large degree,In this paper a general system aimed at dealing with the failure analysis of reinforced concrete columns strengthened with carbon-fiber-reinforced plastic(CFRP) sheets including bond-slip of the anchored reinforcing bars at the foot of the columns is presented.It is based on the yield design theory with a mixed modeling of the structue,according to which the concrete material is treated as a classical two-dimensional continuum ,whereas the longitudinal reinfocing bars are regarded as one-dimensional rods including bond-slip at the foot of the columns,In shear reinforced zones both the shear CFRP sheets and transvers reinforcing bars are incorporated in the analysis throuth a homogenization procedure and they are only in tesion ,The approach is then implemented numerically by means of the finite-element formulation,The numerical procedure produces accurate estimates for the loading-carrying capactiy of the shear members taken as an illustrative application by correlation with the experimental results,so the proposed approach is valid. 相似文献