首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 875 毫秒
1.
Zhu  Yu  Song  Yang  Xu  Likun  Qin  Zhenbo  Song  Shizhe  Hu  Wenbin  Xia  Da-Hai 《天津大学学报(英文版)》2020,26(3):218-227
Stainless steel(SS) is one of the most widely used engineering materials in marine engineering. However, its corrosion in the marine atmospheric environment due to the high concentration of Cl~- is a problem. The SS corrosion is a threat to the development and security of marine industry; therefore, evaluating the corrosion resistance of SSs is necessary. In this work, atmospheric corrosion detection probes based on a symmetrical electrode system were used to study the corrosion behaviors of 304 SS and 2205 duplex stainless steel(DSS) in a simulated marine atmosphere. A theoretical model for electrochemical noise(EN) data analysis based on the Thevenin electrochemical equivalent circuit(EEC) model was established. The relationship between the EN characteristic parameters and the corrosion rate was obtained. The Thevenin EEC model analysis showed that the relationship between the noise resistance( R_n), the noise impedance [ R_(sn)(f)], and the impedance modulus(| Z( f)|) was R_n≈ R_(sn)=■. Thus, R_n and R_(sn) can be used as indicators for quantitative corrosion evaluation. The results of EN detection for the 304 SS and 2205 DSS showed that in a simulated marine atmospheric environment, the passive fi lms on the two SSs were relatively intact at the initial exposure stage, and their dissolution rates were slow. The corrosion resistance of the 2205 DSS was higher than that of the 304 SS. With the deposition of Cl~- on the SS surface, pitting was initiated and the dissolution rate increased. The pitting initiation process on the SS surface was random, and part of the active pores could be repassivated.  相似文献   

2.
Passivity degradation of 304 stainless steel(SS) in simulated alkaline water chemistries at 300℃ was investigated using polarization curve, scanning electron microscope, time-of-flight secondary ion mass spectrometry(SIMS) and X-ray photoelectron spectroscopy(XPS). Experimental results indicated that 304,SS was selfpassive in the test solution and the thickness of passive film was about 500 nm. Hydroxide was enriched in the outer layer whereas oxide was enriched in the inner layer. Sulfur in thiosulfate could be reduced into lower valence of sulfur and enter the passive film so that the composition of passive film was modified by sulfur. Fe and Cr were enriched in the passive film whereas Ni was depleted in the passive film.  相似文献   

3.
Phenolic formaldehyde(PF)and epoxy(EP)resins are commonly used in electronic packaging. In this paper, high-ohmic resistors(2.2 M?, ±0.5%,)with Cr-Si film were coated by PF/EP paint, and the resulting coated resistors were used for heat and humid(HH)experiments. The experimental results show that the corrosion of bandlike resistive films is selective and isotropic, and that the corrosion spots in resistive films all form along grooves and extend in the same direction. It is revealed that OH~- ions are generated due to the electrochemical reactions of resistive film in HH experiments, so a NaOH aqueous solution with pH about 10 was used to study the effects of absorbed water and OH~- ions on PF/EP polymer film. The results indicates that the color of some part on PF/EP polymer film changes due to corrosion, and that the corrosion part of the polymer film is easy to be peeled off. It can be inferred that OH~- ions generated in HH experiments may play a catalytic role in the chemical reactions between polymer film and the absorbed water, which accelerates the degradation of PF/EP protection film for a resistor.  相似文献   

4.
We report the adsorption of phosphate and discuss the mechanisms of phosphate removal from aqueous solution by burst furnace slag （BFS） and steel furnace slag （SFS）. The results show that the adsorption of phosphate on the slag was rapid and the majority of adsorption was completed in 5-10 min. The adsorption capacity of phosphate by the slag was reduced dramatically by acid treatment. The relative contribution of adsorption to the total removal of phosphate was 26%-28%. Phosphate adsorption on BFS and SFS follows the Freundlich isotherm, with the related constants of k 6.372 and 1/n 1.739 for BFS, and of k 1.705 and 1/n 1.718 for SFS. The pH and Ca^2＋ concentration were decreased with the addition of phosphate, suggesting the formation of calcium phosphate precipitation. At pH 2.93 and 6.93, phosphate was desorbed by about 36%-43% and 9%-11%, respectively. These results indicate that the P adsorption on the slag is not completely reversible and that the bond between the slag particles and adsorbed phosphate is strong. The X-ray diffraction （XRD） patterns of BFS and SFS before and after phosphate adsorption verify the formation of phosphate salts （CaHPO4·2H2O） after adsorption process. We conclude that the removal of phosphate by BFS and SFS is related to the formation of phosphate calcium precipitation and the adsorption on hydroxylated oxides. The results show that BFS and SFS removed phosphate nearly 100%, indicating they are promising adsorbents for the phosphate removal in wastewater treatment and pollution control.  相似文献   

5.
Corrosion of steel rebar is the most important durability problem of reinforced concrete. The aim of this research was to investigate the corrosion behavior of steel rebar in simulated pore solutions and gangue-blended cement mortar. The simulated pore solutions were based on the pore solution composition ofgangue-blended cement. The pH and CI concentration of simulated pore solutions had significant effects on corrosion potential. However, an increase in pH reduced the influence of Cl- concentration on corrosion potential. The corrosion behavior of steel rebar in gangue-blended cement is different from that in simulated solutions. The gangue cementitious mortar surrounding steel rebar provides stable passivity environments for steel, leading to a decrease in ion diffusion coefficients. Alternating current impedance （ACI） analysis results indicated that the indicator Rc for concrete resistivity is higher for gangue mortar than for ordinary Portland cement （OPC）, which improves its corrosion potential. The results from energy dispersive X-ray analysis （EDX） showed more aluminates and silicates at the rebar interface for gangue-blended cement. These aluminates improve the chloride binding capacity of hydrates in mortar, and increase the corrosion protection of steel rebar.  相似文献   

6.
The corrosion process of tinplate in deaerated functional beverage was investigated by using electrochemical impedance spectroscopy (EIS) combined with scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) techniques. The results reveal that the uncoated tinplate shows a poor corrosion resistance and the corrosion type is detinning. During the initial stage of immersion, EIS spectrum consisted of two capacitance arcs with obvious time-constant dispersion effect, which was attributed to the two-dimensional and three-dimensional inhomogeneous distribution of the electrode surface. With the increase of immersion time, the capacitance arc of high frequency shrunk and degenerated, due to the corrosion of tin coating. The pore resistance of tin coating and the charger transfer resistance of substrate, which are determined from the electrochemical equivalent circuit, can be used as the indicators of tinplate corrosion process. The decrease of the pore resistance of tin coating indicates that the corrosion degree of tin layer becomes more severe, whereas the decrease of the charger transfer resistance of substrate implies that the corrosion degree of steel substrate also becomes more severe as the immersion time prolongs.  相似文献   

7.
Passivity degradation of Alloy 800 in simulated crevice chemistries was systematically investigated using cyclic polarization curve, electrochemical impedance spectroscopy(EIS), Mott-Schottky analysis, Auger electron spectroscopy(AES)and atomic absorption spectrometry(AAS). Cyclic polarization showed that the pitting potential in a thiosulfate solution was much lower than in either a chloride solution or a sulfate-chloride solution. Mott-Schottky results revealed that passive films showed n-type semiconductivity, and the presence of thiosulfate in chloride solution led to an increased donor density in the passive film. EIS spectra indicated that thiosulfate enhanced the film dissolution rate in chloride solutions. Moreover, thiosulfate enhanced the pitting propagation rate in chloride solution by stabilizing the metastable pits and forming sulfide within the pits.  相似文献   

8.
Biochar is a potential carrier for nutrients due to its porous nature and abundant functional groups. However, raw biochar has a limited or even negative capacity to adsorb phosphate. To enhance phosphate removal and reduce phosphate releases, acidic, alkaline, and surfactant pretreatments,followed by granulation and ferric oxide loading, were applied to raw biochar powder(B_p). The alkaline pretreatment proved to be the most effective method and exhibited significant pore expansion and surface oxidation. B_g-OH-FO showed the highest phosphate removal efficiency at 99.2%(initial phosphate concentration of 20 mg/L) after granulation and ferric oxide loading. Static adsorption results indicated that a p H value of 4 was the most suitable for phosphate adsorption because of the surface properties of B_g-OH-FO and the distribution of P(V) in water. Higher temperatures and a larger initial phosphate concentration led to better adsorption; the adsorption capacity of B_g-OH-FO was 1.91 mg/g at 313 K with an initial phosphate concentration of 50 mg/L. The B_gOH-FO adsorption process was endothermic in nature. The Freundlich model seemed to be the optimum isotherm model for B_g-OH-FO. Under continuous adsorption, the flow rate and bed depth were changed to optimize the operation conditions. The results indicate that a slow flow rate and high bed depth helped increase the removal efficiency(g) of the fixed bed. The breakthrough curves fitted well with the Yoon–Nelson model.  相似文献   

9.
A specialised electrochemical measurement cell was plugged into a pilot water distribution system to simulate the pipe inner-wall corrosion. The linear polarisation resistance(LPR) technique and electrochemical impedance spectroscopy(EIS) were measured in real time to study the variation of the corrosion rate(CR) and scale of cast iron. Three corrosion stages were observed according to the LPR analysis: an initial stage with significantly fluctuating CR, a developmental stage with slowly decreasing CR, and a stable stage with a low CR of approximately 0.157 5 mm·a~(-1). The EIS revealed that the scales with a compact outer layer and a porous inner layer finally formed in the stable stage, and the polarisation resistance was approximately 2 175 ?·cm~2. A physicochemical analysis of the scales showed that ferric oxides, oxyhydroxides and calcite made the outer layer compact and effectively limited the diffusion of oxygen through the scales, which resulted in a low CR.  相似文献   

10.
唐磊  江晓敏 《海外英语》2013,(15):93-94
The present study investigated one Chinese college learner’s requesting performance by analyzing the DCT data produced in four different situations.The results indicated that the learner favored the indirect strategy in all four situations,and was able to produce longer requests with a large portion of external modification.However,the learner lacked sufficient knowledge and ability to control over a wide range of internal modification,relied heavily on external modification,produced lengthy grounders,and failed to show enough sensitivity to imposition variation.  相似文献   

11.
In order to research the bond properties between corroded reinforcement bars and concrete, reinforcement bars with different diameters and different types and concrete with different strength levels were treated specially with all soaking and impressed current method, and the bond properties were measured with the pull-out test. The comparative analysis of the bond properties of corroded reinforcement bars was carried out. The results showed that the types of reinforcement bars and concrete had great influence on the bond strength. The corrosion and volume expansion of reinforcement bars made concrete in tensile condition, which tended to produce cracks in parallel reinforced direction. The typical bond failure of plain reinforcement bars was pull-out, while the typical bond failure of ribbed reinforcement bars was split. The bond strength between corroded reinforcement bars and concrete increased with the increase of concrete strength. The bond strength of plain and ribbed reinforcement bars showed a decreasing trend after the first increase with the increase of the extent of corrosion. Through the test, the coefficients of the bond strength of plain and ribbed reinforcement bars were given, respectively.  相似文献   

12.
This paper presents the research on the atmospheric corrosion rates of carbon steel, zinc and copper in Chongqing, which was a corrosion subprogram of an international project, Regional Air Pollution in Developing Countries. We performed field exposure tests of carbon steel, zinc and copper at an urban site Guanyinqiao and a rural site Tieshanping inChongqing, then used grey relational analysis, based on the database of the whole corrosion project, to determine the order of the effect of environmental factors on corrosion rates of tested metals, and established dose-response functions for these three metals. The results showed that the two crucial agents of acidic environment, SO2 and H , were common factors that contributed most to the corrosion of the tested metals. The established dose-response functions for outdoor carbon steel and zinc are proved applicable to use in Chongqing, but the function for copper needs further modifying. We employed these dose- response functions and general environmental data to elaborate the maps of corrosion rate respectively of carbon steel and zinc by geological information system (GIS) technique which help to identify areas of high corrosion damage risk. An acceptable annual average SO2 level of 21 μg/m3 for carbon steel and that of 61 μg/m3 for zinc are also put forward to control the air pollution impact on atmospheric corrosion in Chongqing urban areas.  相似文献   

13.
An Mg-Zn-Mn-Ca alloy with high Zn content was fabricated by vacuum melting. The as-cast microstructure was investigated using XRD, SEM and EDS. It was shown that the alloy was composed of α-Mg, strip-like Ca2Mg6Zn3 and a few Mn- containing phases. Most of the Ca2Mg6Zn3 phase was distributed at grain boundaries while Mn-containing particles were deposited within grains. The as-cast samples were immersed in a Hank＇s balanced salt solution （HBSS） up to 24 h. The corroded surface morphology and cross-section microstructure were analyzed after different time of immersion so as to understand the corrosion behavior of the alloy. During immersion in the HBSS, the alloy corroded homogeneously at the very beginning and then localized corrosion occurred. The secondary phases protruded on the surface due to the dissolution of α-Mg, suggesting micro- galvanic corrosion occurred with secondary phases acting as the cathode and ct-Mg as the anode. Micro-cracks were formed at the interfaces between Ca2Mg6Zn3 and α-Mg, indicating an undermining tendency of the secondary phases.  相似文献   

14.
INTRODUCTION New topological method in complementaritytheory is now developing. This method is based on thenotion of “exceptional family of elements (EFE)”initially defined in 1991–1993 by G. Isac as “radialfamily of elements”. The name of EFE was given in(Isac et al., 1997), after the authors found a connectionbetween this notion and the topological degree in Rn. We note that after 1997, this notion was extendedto completely continuous fields and to other classes ofm…  相似文献   

15.
INTRODUCTION Steel rebar embedded in concrete is protectedagainst corrosion by the thin passive film on its sur-face and the physical protection from concrete. Thealkaline environment (pH≥12.5) of the concrete poresolution triggers passivation on the rebar surface andformation of the protective oxide film. The physicaprotection of concrete coverage hinders the invasionof aggressive agents. However, this passivity can bebroken down by local pH loss as a result of concretecracking or the…  相似文献   

16.
In this study, a new mass model involving superheat, initial temperature, liquid height, evaporator diameter, and flashing time is established to describe the flash evaporation process of water film. Of 469 sets of flash experimental data from three previous researches, 305 sets were applied to optimize parameters, and the other 164 sets were used to verify the practicability of the model. The results showed that the mean relative error between the literature data and the model values was less than 16.3%, and the model statistics proved that the model was well-posed. Then, the kinetic model was obtained using the time derivative of the new mass model. Computational fluid dynamics simulation of water film flash evaporation was studied based on a user-defined function program of the new evaporation kinetic model. The new kinetic model shows more consistency with the experimental phenomena in terms of evaporated mass and temperature compared with the evaporation–condensation model in Fluent software and Gopalakrishna's model. This new kinetic model can be extended to describe the flash process of water solution under other conditions.  相似文献   

17.
Kevin Spacey was born in New Jersey on July 26th, 1959. The family moved to Southern California and the boisterous (狂暴喧闹的) Spacey found himself sent off to a military academy. When that school couldn' t tame him, he moved on to Chatsworth High School, where he met other future actors Mare Winningham and Val Kilmer.In 1984, he found himself understudying (练习做临时演员) all the male roles in Hurlyburly. Director Mike Nichols was so impressed by his versatility (多才多艺) that he made sure he had a chance to play all of the roles during the run. After that he managed to land the lead role of National Anthems after Al Pacino dropped out and in 1986 starred opposite Jack Lemmon in the Broadway revival of Long Day' s Journey Into Night.Kevin made his film debut in 1986' s Heartburn and made  相似文献   

18.
Microcystis aeruginosa FACHB 905 was used as a model organism to study the effects of small water clusters(SWCs) on the growth and microcystin(MC) production of toxic cyanobacteria.The results showed that SWCs were able to stimulate the growth of Microcystis aeruginosa,which resulted in increased cell numbers and higher specific growth rates after a 30-d treatment.The cell morphology indicated that Microcystis aeruginosa was in a better state of growth,and it was more prone to divide in SWCs than in normal water clusters.The SWCs treatment up-regulated MC synthesis and exudation in 10 d in Microcystis aeruginosa,and the intra-cellular MC content decreased after the 20th day subsequently.Moreover,the cellular photosynthetic pigment contents were temporarily stimulated by SWCs.A possible reason is that SWCs stimulated the growth by promoting photosynthesis,whereas the increased MC production was relevant to pigment contents.  相似文献   

19.
A parallel dynamic passive valveless micropump was designed, which consists of three layers-valve, diaphragm and electromagnetic coil. The valve was wetly etched in a silicon wafer, the diaphragm was a PDMS （polydimethyl siloxane） film spun on a silicon wafer with embedded permanent magnet posts, and the coil was electroplated on a silicon substrate. Under the actuation of the magnetic field generated by coils, the flexible diaphragm could be displaced upwards and downwards. After analyzing magnetic and mechanical characteristic of the flexible membrane and direction-dependence of the nozzle, a micropump was designed. And the relative length （L/d） of the micropump nozzle was taken 4. A 7 × 7 array of permanent magnetic posts was embedded in the PDMS film. Two diaphragms worked in an anti-step mode, which could relieve the liquid shock and increase the discharge of the micropump. The ANSYS and Matlab were adopted to analyze the actuation effect of the coil and the flow characteristic of the micropump. Results show that when actuated under a 0.3 A, 100 Hz current, the displacement of the diaphragm is more than 30 μm, and the discharge of the micropump is about 6 μL/s.  相似文献   

20.
Nominal contact resistance, minimum erosion and material transfer are required with low cost materials working in a wide currents range for DC relays. Ag-Ni contact materials have low contact resistance, but the erosion and material transfer are large at high current level. Ag-SnO2 contact materials have good anti-welding properties and resistance to arc erosion, but they have large contact resistance during working and are easily block SnO2 from flocking together on the surface at low current level. In this paper, the failure mechanisms of Ag-Ce contact material were studied. The surface morphologies of the contacts after electrical endurance test for Ag-Ce contact material were compared with that of Ag-Ni and Ag-SnO2 contact materials. The effect of Ce on the surface morphologies of the contacts after electrical endurance test was analyzed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号