共查询到16条相似文献，搜索用时 625 毫秒
1.
对15根玻璃纤维布加固的钢筋混凝土梁进行了试验研究。试验结果表明,玻璃纤维布加固的钢筋混凝土梁抗弯承载力显著提高,加固效果明显,但要有足够的粘贴长度以避免发生剥离破坏。 相似文献
2.
为了解玻璃纤维(GFRP)布与钢筋混凝土梁界面之间的粘结性能,进行了7根GFRP布加固的钢筋混凝土梁与2根对比梁的试验研究.试验的变化参数为GFRP布层数、粘结长度及配筋率.试验结果表明,GFRP布加固的钢筋混凝土梁极限荷载显著提高,但是发生剥离破坏的试验梁极限荷载有所降低,粘结长度是影响加固梁剥离破坏的主要因素.根据试验结果提出了GFRP布与钢筋混凝土梁界面粘结剪应力的试验分析方法并分析了界面间粘结剪应力的分布.同时,提出了GFRP布加固的钢筋混凝土梁剥离正应力与粘结剪应力的理论分析方法.最后,给出了GFRP布加固钢筋混凝土梁剥离荷载的计算方法.为验证理论分析方法的正确性,计算了试验梁界面间的粘结剪应力、剥离正应力及剥离荷载.计算结果表明,所提出的理论分析方法与试验值吻合较好. 相似文献
3.
通过9根表层嵌入碳纤维增强塑料板条抗剪加固的钢筋混凝土梁和4根对比梁的静载试验,分析了构件的破坏形态、斜截面纤维应变分布特征及加固后极限承载力的影响因素。研究结果表明：嵌入式加固与外贴加固相比,可以明显地提高钢筋混凝土梁的抗剪承载力,并改变构件的变形性能。最后,在国内外研究资料的基础上,提出了加固后混凝土梁的受剪承载力计算公式,并对计算值与试验值进行了比较,结果吻合较好。 相似文献
4.
二次受力下碳纤维布加固梁抗弯性能试验研究 总被引：1，自引：0，他引：1
进行了4根不同二次受力条件下碳纤维布加固的钢筋混凝土梁和1根对比混凝土梁的抗弯性能试验研究。试验及分析结果表明,用粘贴碳纤维布的方法来提高梁的承载力十分有效,且预加载的存在使加固梁的极限荷载降低;碳纤维布能有效约束裂缝的开展,但裂缝的数量增加和分布区域变大,且预加载的大小会影响加固梁裂缝的开展和分布;碳纤维布加固可以增强梁的刚度,但延性有所降低。 相似文献
5.
通过制作1根普通混凝土深梁和8根沙漠砂混凝土深梁来研究沙漠砂掺量、剪跨比、箍筋配筋率和混凝土强度等级对沙漠砂混凝土深梁挠度和短期刚度的影响,并采用中国混凝土结构设计规范和有效惯性矩法对深梁试件短期刚度进行理论值计算.结果表明:沙漠砂混凝土深梁试件跨中挠度随剪跨比和箍筋配筋率的增大而增大,随混凝土强度等级的增大而减小,随... 相似文献
6.
为研究碳纤维布(CFRP)对加固后钢筋混凝土梁的抗弯疲劳性能的影响,进行了3根CFRP加固梁及1根对比梁的抗弯疲劳试验.研究了碳纤维布加固方式、构件使用荷载等参数对碳纤维布加固损伤钢筋混凝土吊车梁的抗弯疲劳性能影响.试验研究表明:采用碳纤维布加固后,构件裂缝的宽度减小50.2%~66%,发展速度也得到控制,钢筋应力减小24.1%~28.2%,构件的刚度提高14.9%~16.1%.依据试验结果,从现有规范中关于构件刚度计算方法出发,进行了CFRP加固钢筋混凝土吊车梁的疲劳刚度计算分析,该计算方法可用于吊车梁加固工程设计.最后给出了CFRP加固梁的疲劳设计的合理化建议. 相似文献
7.
采用Ansys有限元软件对8根不同锈蚀率的FRP片材加固钢筋混凝土梁的受弯性能进行数值分析,研究纵筋锈蚀率对FRP加固梁的裂纹开展、破坏模式、承载能力以及延性和变形能力的影响.研究结果表明:低钢筋锈蚀率的梁发生受压区混凝土压碎破坏;中等锈蚀率的梁钢筋屈服后,钢筋与混凝土界面发生黏结滑移,最后FRP剥离破坏;高锈蚀率的梁钢筋没有达到屈服强度便发生黏结滑移,最后发生受压区混凝土压碎破坏.钢筋锈蚀越严重,FRP加固钢筋混凝土梁的承载力降低得越多.试件RCB-1(锈蚀率为0)的承载力为115 kN,而试件RCB-7(锈蚀率为20%)的承载力仅为42 kN.与FRP加固未锈蚀的钢筋混凝土梁相比,FRP加固锈蚀钢筋混凝土梁的变形能力较高.试件RCB-1和试件RCB-7的最大跨中挠度分别为20 mm和35 mm,而试件RCB-5(锈蚀率为10%)的最大跨中挠度达到了60 mm. 相似文献
8.
以7根1:3模型梁为研究对象,试验研究箱形型钢混凝土(SRC)梁的性能.试验结果表明,箱形SRC梁的抗弯强度随纵筋配筋率和型钢翼缘板厚度的增大而提高,剪切强度随型钢腹板的厚度增大而提高.箱形型钢内浇注混凝土不但可避免型钢屈曲破坏而且还可提高梁的极限荷载.型钢和混凝土间的连接需要改善以加强混凝土和型钢的共同工作作用.给出了箱形SRC组合梁的抗弯承载力和抗剪承载力计算公式,计算结果和试验结果吻合良好.箱形SRC组合梁是一种延性构件,适用于工程实践应用. 相似文献
9.
为研究无机胶粘贴碳纤维布对钢筋混凝土梁高温性能的影响,对3根不同加固方式及防火方式的钢筋混凝土梁进行高温试验。试验结果表明,无机胶及防火涂料对钢筋混凝土梁温度场及跨中挠度有重要作用;与防火性能较差的有机胶相比,无机胶具有较好的耐高温性能,可应用于碳纤维布加固混凝土工程中;防火涂料在火灾过程中具有较好的防火和隔热作用,在防火设计中不可忽略。 相似文献
10.
通过碳纤维薄板补强钢筋混凝土梁的抗弯试验，采用改变碳纤维薄板粘贴长度、梁的缺口高度和配筋率等参数，对加固梁的界面破坏形式进行了较系统的试验研究，并初步分析了界面的剥离失效机理。 相似文献
11.
Carbon fiber reinforced polymer(CFRP)bars were prestressed for the structural strengthening of 8 T-shaped rein-forced concrete (RC)beams of a 21-year-old bridge in China.The ultimate bearing capacity of the existing bridge after retrofit was discussed on the basis of concrete structures theory.The flexural strengths of RC beams strengthened with CFRP bars were controlled by the failure of concrete in compression and a prestressing method was applied in the retrofit.The field construction processes of strengthening with CFRP bars-including grouting cracks,cutting groove,grouting epoxy and embedding CFRP bars,surface treating,banding with the U-type CFRP sheets,releasing external prestressed steel tendons-were introduced in detail.In order to evaluate the effectiveness of this strengthening method,field tests using vehicles as live load were applied before and after the retrofit.The test results of deflection and concrete strain of the T-shaped beams with and without strengthening show that the capacity of the repaired bridge,including the bending strength and stiffness,is enhanced.The measurements of crack width also indicate that this strengthening method can enhance the durability of bridges.Therefore,the proposed strengthening technology is feasible and effective. 相似文献
12.
Feras ALZOUB ZHANG Qi LI Zheng-liang 《重庆大学学报(英文版)》2007,6(4):305-310
This paper presents the results of an experimental investigation on the response of pre-damaged reinforced concrete (RC) beam strengthened in shear using applied-epoxy unidirectional carbon fiber reinforced polymer (CFRP) sheet. The reasearch included four test rectangular simply supported RC beams in shear capacity. One is the control beam, two RC beams are damaged to a predetermined degree from ultimate shear capacity of the control beam, and the last beam is left without pre-damaged and then strengthened with using externally bonded carbon fiber reinforced polymer to upgrade their shear capacity. We focused on the damage degree to beams during strengthening, therefore, only the beams with side- bonded CFRPs strips and horizontal anchored strips were used. The results show the feasibility of using CFRPs to restore or increase the load-carrying capacity in the shear of damaged RC beams. The failure mode of all the CFRP-strengthened beams is debonding of CFRP vertical strips. Two prediction available models in ACI-440 and fib European code were compared with the experimental results. 相似文献
13.
Carbon fiber reinforced polymer （CFRP） bars were prestressed for the structural strengthening of 8 T-shaped reinforced concrete （RC） beams of a 21-year-old bridge in China. The ultimate bearing capacity of the existing bridge after retrofit was discussed on the basis of concrete structures theory. The flexural strengths of RC beams strengthened with CFRP bars were controlled by the failure of concrete in compression and a prestressing method was applied in the retrofit. The field construction processes of strengthening with CFRP bars including grouting cracks, cutting groove, grouting epoxy and embedding CFRP bars, surface treating, banding with the U-type CFRP sheets, releasing external prestressed steel tendons-were introduced in detail. In order to evaluate the effectiveness of this strengthening method, field tests using vehicles as live load were applied before and after the retrofit. The test results of deflection and concrete strain of the T-shaped beams with and without strengthening show that the capacity of the repaired bridge, including the bending strength and stiffness, is enhanced. The measurements of crack width also indicate that this strengthening method can enhance the durability of bridges. Therefore, the proposed strengthening technology is feasible and effective. 相似文献
14.
INTRODUCTION Externally bonded fiber reinforced polymer (FRP) composites can be used to improve the flexural strength of structural members. To evaluate the flex-ural performance of the strengthened members, it is necessary to study the flexural stiffness of FRP- strengthened RC members at different stages, such as pre-cracking, post-cracking and post-yielding. Up to now, only very few studies were focused on the structural members strengthened under pre-loading or pre-cracking (Arduin… 相似文献
15.
INTRODUCTION The aging or deterioration of existing R. C.(reinforced concrete) or P. C. (prestressed concrete)structures is one of the major problems that modernengineers have to face. If the flexural or shear strengthof R. C. or P. C. structures is not sufficient to maintaintheir service functions, strengthening of these struc-tures becomes necessary. To date, steel plates havebeen used to strengthen concrete members. Usingcomposite plates to strengthen R.C. or P.C. structures… 相似文献
16.
FRP加固RC圆柱正截面受弯承载力计算（英文） 总被引：1，自引：0，他引：1
运用数值计算方法对FRP加固钢筋混凝土（RC）圆柱截面特性进行计算,发现截面破坏时受压区高度主要受轴压比、FRP约束强度比和纵筋配筋特征值3个主要参数影响.根据数值计算的结果进行回归,提出了受压区对应圆心角θ的计算方法.数值计算结果显示,横向约束导致的混凝土应力提高以及纵筋屈服后的强化效应使RC柱破坏时截面受弯承载力远大于规范规定值.根据理论分析和36个大比例试件实测结果提出截面破坏时受弯承载力计算方法,计算结果与试验结果吻合很好.最后,对一个典型柱变形能力进行参数分析,研究轴压比,纵筋配筋特征值和FRP约束强度比对正截面变弯承载力的影响.结果显示FRP加固圆柱破坏时受弯承载力可以比规范规定的未加固柱受弯承载力提高50%左右. 相似文献