共查询到20条相似文献，搜索用时 156 毫秒
1.
Seismic behavior of steel reinforced ultra high strength concrete column and reinforced concrete beam connection 总被引：1，自引：1，他引：0
To investigate the seismic behavior of connections composed of steel reinforced ultra high strength concrete （SRUHSC） column and reinforced concrete （RC） beam, six interior strong-column-weak-beam connection specimens were tested subjected to reversal cyclic load. Effects of applied axial load ratio and volumetric stirrup ratio on ductility, energy dissipation capacity, strength degradation and rigidity degradation were discussed. It was found that all connection specimens failed in bending in a ductile manner with a beam plastic hinge. The ductility and energy dissipation capacity increased with the decrease of applied axial load ratio or increase of volumetric stirrup ratio. The displacement ductility coefficient and equivalent damping coefficient lay between those of steel reinforced ordinary concrete connection and those of reinforced concrete connection. The applied axial load ratio and volumetric stirrup ratio had less influence on the strength degradation and more influence on the stiffness degradation. The stiffness degraded sharply with the decrease of volumetric stirrup ratio or increase of applied axial load ratio. The experimental results indicate that SRUHSC column and RC beam connection exhibited better seismic performance and can provide reference for engineering application. 相似文献
2.
The seismic performance of four short concrete columns was investigated under low cycle and repeated loads, including the failure characteristics, hysteretic behavior, rigidity degeneracy and steel-bar stress. The influences of reinforcement strength, stirrup ratio and shear span ratio were also compared. Test results reveal that the restriction effect of stirrups can improve the peak stress, so the bearing capacity of specimen can be improved; for the high-strength short concrete column with high-strength stirrups, it was more reasonable to use ultimate displacement angle to reflect the ductility of the specimen, and the yield strength of high-strength stirrups should be devalued when calculating the stirrup characteristic value; the seismic performance of short column would be improved with the increase of volume–stirrup ratio and shear span ratio;the high-strength stirrups and high-strength longitudinal reinforcements did not yield when the load acting on the specimen reached the peak value, which brought adequate safety stock to these short columns. 相似文献
3.
Based on a series of previous studies, an experiment on the integral seismic behavior of a 1/3 scaled model of two-bay and three-story reinforced concrete frame with split columns at lower two stories is performed under cyclic loading. The original columns at lower two stories of the model frame are short columns and they are replaced by the split columns. The hysteresis curves between the horizontal cyclic load and the lateral displacement at the top of the model frame, indicate that under the cyclic loading, the model frame undergoes the process of cracking, yielding, and maxi-mum loading before being destroyed at the ultimate load. They also indicate that the model frame has better ductility, and the ratio of the ultimate displacement to the yielding displacement, reaches 6.0. The yielding process of the model frame shows that for the frame with split columns, plastic hinges are generated at the ends of beams and then the columns begin yielding while the frame still possesses the bearing and deformation capacity. The design idea of directly changing the short col-umn to long one in the reinforced concrete frame may be realized by replacing the short column with the split one. 相似文献
4.
碳纤维布与钢构套复合加固锈蚀钢筋混凝土柱抗震性能研究(英文) 总被引：1，自引：0，他引：1
为改善锈蚀钢筋混凝土柱的抗震性能, 利用碳纤维布与角钢对锈蚀柱进行复合抗震加固. 试验共对12根试件进行了低周反复加载试验, 研究参量包括钢筋锈蚀程度、轴向荷载、碳纤维布层数和角钢用量. 试验结果表明, 利用碳纤维布和角钢复合加固锈蚀柱可以显著改善锈蚀柱的承载能力、延性和耗能能力. 复合加固后, 加固柱的强度和延性与锈蚀柱相比, 可分别提高0.9倍和1倍以上. 基于试验结果, 提出了计算加固构件屈服荷载、最大荷载和位移延性系数的简化公式, 计算结果与试验结果极为吻合. 相似文献
5.
Prestressed steel ultrahigh-strength reinforced concrete (PSURC) beam is a new type of prestressed concrete beam, which not only has a considerable compressive strength attributed to the ultrahigh strength concrete, but also ensures a certain degree of ductility at failure due to the existence of structural steel. Five of these beams were monotonically tested until shear failure to investigate the static shear performance including the failure pattern, load-deflection behavior, shear capacity, shear crack width and shear ductility. The experimental results show that these beams have superior shear capacity, crack control ability and shear ductility. To study the shear performance under repeated overloading, seven PSURC beams were loaded in cyclic test simultaneously. The overall shear performance of cycled beams is similar to that of uncycled beams at low load level but different at high load level. The shear capacity and crack control ability of cycled beams at high load level are reduced, whereas the shear ductility is improved. In addition, the influences of variables including the degree of prestress, stirrup ratio and load level on the shear performance of both uncycled and cycled beams were also discussed and compared, respectively. 相似文献
6.
7.
《天津大学学报(英文版)》2015,(4)
Nonlinear finite element analysis and parametric studies were carried out to study the influence of axial load ratio on the shear behavior of the through-diaphragm connections of concrete-filled square steel tubular columns. The analysis reveals that smaller axial load ratio can improve the shear bearing capacity and ductility while larger axial load ratio will decrease the shear behavior of the through-diaphragm connections. The parametric studies indicate that the axial load ratio should be limited to less than 0.4 and its influence should be considered in the analysis and design of such connections. 相似文献
8.
To investigate the seismic behavior of specially shaped column joints with X-shaped reinforcement,two groups of specimens with or without X-shaped reinforcement in joint core region were tested under constant axial compression load and low reversed cyclic loading,which imitated low to moderate earthquake force.The seismic behavior of specially shaped column joints with X-shaped reinforcement in terms of bearing capacity,displacement,ductility,hysteretic curve,stiffness degradation and energy dissipation was studied and compared to that without Xshaped reinforcement in joint core region.With the damage estimation model,the accumulated damage was analyzed.The shearing capacity formula of specially shaped column joints reinforced by X-shaped reinforcement was proposed with a simple form.The test results show that X-shaped reinforcement is an effective measure for improving the seismic behavior of specially shaped column joints including deformation behavior,ductility and hysteretic characteristic.All specimens were damaged with gradual stiffness degeneration.In addition,X-shaped reinforcement in the joint core region is an effective way to lighten the degree of cumulated damage.The good seismic performance obtained from the specially shaped column joint with X-shaped reinforcement can be used in engineering applications.The test value is higher than the calculated value,which indicates that the formula is safe for the design of specially shaped column joints. 相似文献
9.
彭燕 《杨凌职业技术学院学报》2014,(1):10-12
采用ANSYS软件进行了数值模拟,分别对比了三种型钢截面形式和i种轴压比对型钢高强混凝土柱的延性和耗能性能的影响。从计算结果可以看出,轴压比越小,延性系数越大,抗震性能越好;带翼缘十字形型钢柱的延性比不带翼缘十字形型钢柱的延性好。 相似文献
10.
Ten slender steel reinforced cencrete (SRC) composite columns are tested under eccentric loading conditions.Effects of concrete strength, slenderness of columns and eccentricity of the axial load are studied. The load-carrying capacity is reduced with increased slenderness ratio and eccentricity. Concrete strength has no obvious influence on eccentrically loaded columns. Then, a nonlinear numerical method of pin-ended slender columns is also presented. This method is applicable for determining the material failure load or buckling failure load of a slender steel reinforced concrete composite column. In this method both material and geometric nonlinearities are taken into account. The results of numerical analysis accord well with the test results. The test results are also compared with the results predicted by ACI318-05 and the China Specifications. 相似文献
11.
The stress-strain curves of confined concrete were obtained based on tests of seven cross-shaped columns confined by stirrups under axial load. The experiment results showed that the strength and deformation of confined concrete can be enhanced effectively by stirrups for cross-shaped columns. Compared with the non-confined concrete, when the stirrup characteristic value is in the range of 0.046--0.230, the confined concrete compressive strengths has an increase of 8%--43%, and the strain corresponding to the peak stress of confined concrete has an increase of 25%-- 195%. According to the test results, the effects of stirrup characteristic and stirrup spacing on the compressive strength and strain of confined concrete were analysed. It is shown that the compressive strength of confined concrete has a linear relationship with the product of stirrup characteristic value and stirrup effective restraint coefficient, and the strain corresponding to the peak stress of confined concrete has a nonlinear relationship with the product of stirrup characteristic value and stirrup effective restraint coefficient. The stress-strain curve equation of confined concrete was proposed for cross-shaped columns, and the calculated curves are in good agreement with the experimental curves. 相似文献
12.
FRP加固RC圆柱正截面受弯承载力计算（英文） 总被引：1，自引：0，他引：1
运用数值计算方法对FRP加固钢筋混凝土（RC）圆柱截面特性进行计算,发现截面破坏时受压区高度主要受轴压比、FRP约束强度比和纵筋配筋特征值3个主要参数影响.根据数值计算的结果进行回归,提出了受压区对应圆心角θ的计算方法.数值计算结果显示,横向约束导致的混凝土应力提高以及纵筋屈服后的强化效应使RC柱破坏时截面受弯承载力远大于规范规定值.根据理论分析和36个大比例试件实测结果提出截面破坏时受弯承载力计算方法,计算结果与试验结果吻合很好.最后,对一个典型柱变形能力进行参数分析,研究轴压比,纵筋配筋特征值和FRP约束强度比对正截面变弯承载力的影响.结果显示FRP加固圆柱破坏时受弯承载力可以比规范规定的未加固柱受弯承载力提高50%左右. 相似文献
13.
本文采用低强箍筋和高强箍筋的对比试验,对高强混凝上压弯构件进行了在反复荷载作用下的试验,得到了各试件的荷载-位移府回曲线,通过对荷载-位移滞回曲线、位移延性系数等的分析,研究了冷轧带肋钢筋作箍筋对高强混凝土柱延性的影响试验表明：高轴压比下的高强混凝土柱在高强度箍筋─—冷轧带肋钢筋、高配箍率下能获得很好的延性． 相似文献
14.
陈鹏 《泰州职业技术学院学报》2008,8(3):5-6
《混凝土异形柱结构技术规程（JGJ149—2006）》提出按照最小配箍特征值确定箍筋加密区体积配箍率要求,相应箍筋配置方案需通过计算求得,应用不便。按《规程》要求,根据异形柱的抗震等级、截面形式与尺寸、混凝土强度等级、轴压比的大小,给出了具体的箍筋配置方案,并形成图表,方便设计人员设计、核查。 相似文献
15.
A pseudo-dynamic testing program was generated on a fabricated composite frame with steel plate shear walls (SPSWs) to study its seismic performance. The specimen was a three-storey single-bay frame, which was composed of H-section steel columns and composite beams, and was assembled by bolted height-adjustable steel beam-to-column connections (BHA connections). Beam-only-connected SPSWs were selected as lateral load resisting members. The specimen was subjected to four ground motions of progressively increasing intensity. The results showed that: (1) beam-only-connected SPSWs provided sufficient lateral load resistance, lateral stiffness, and energy dissipation capacity to the fabricated frame via the tension field action developed in their infill panels; (2) the fabricated frame, assembled by BHA connections, exhibited substantial redundancy and good ductility; (3) an undesirable failure mode of the fabricated frame, in huge earthquakes, included severe cracking in composite beams and block shear failure in SPSWs’ connections; (4) the inter-storey shear force distribution determined by ASCE/SEI 7-10 was verified with experimental data. 相似文献
16.
本文采用框架加荷系统对高强砼柱进行了反复荷载下的试验。以位移延性系数为指标,对影响高强砼柱延性的各因素进行了分析,提出了高强砼柱轴压比的限值和柱加密区箍筋最小体积含箍率的建议值,对高强砼偏心受压柱强度计算的基本假定进行了修正。供设计人员参考。 相似文献
17.
18.
探讨钢筋混凝土T形柱最不利荷载角及其影响因素.利用编制的钢筋混凝土异形柱截面全过程数值分析程序,通过对多种工况下钢筋混凝土异形柱正截面承载力的计算分析,结果表明异形柱最不利荷载角的影响因素主要是轴压比;截面尺寸对最不利荷载角有些影响;而混凝土强度、纵筋配筋面积对最不利荷载角的影响很弱.研究结果为钢筋混凝土异形柱的设计和异形柱的可靠性分析提供参考依据. 相似文献
19.
因为异形柱经常承受偏心受压加受扭的复杂受力,所以理论计算比较复杂。本研究使用有限元分析软件ABAQUS对T形截面型钢混凝土柱的抗扭性能进行了数值模拟分析,并考虑混凝土塑性发展探讨不同轴压比与钢骨率对型钢混凝土T形截面柱延性与抗扭承载力的影响。利用已有的实验数据,建立构件的受压有限元模型,通过对比荷载-位移曲线验证有限元材料本构的有效性。建立三组模型分析不同轴压比与钢骨率对构件抗扭力学性能的影响,为今后型钢混凝土异形柱的应用提供参考。 相似文献
20.
运用ANSYS软件,对宽扁梁柱节点进行有限元分析,重点研究了轴压比对模型的承载力、梁端位移及荷载位移曲线的影响,认为合理控制轴压比在0.2~0.7的范围内,能使结构具有较高的承载力及较大的刚度,这就为宽扁梁在实际工程中的应用提供理论依据。 相似文献