共查询到20条相似文献，搜索用时 582 毫秒
1.
The resonant tunneling diode (RTD) is an ultra-highspeed and ultra-high frequency quantum-transport deviceaccompanied with negative differential resistance (NDR)I-Vcharacteristic originating fromresonant tunneling effect .The core structure of RTDis doubl… 相似文献
2.
Based on planar Si dual-base transistor conception, a novel mesa dual-base heterojunction bipolar transistor （ HBT） is designed and fabricated. Molecule beam extension, selective wet chemical etching, common contact photolithography and metal lift-off technique are adopted in the process. The device has particular and distinct voltage-controlled negative differential resistance （NDR） and photo-controlled NDR. The highest peak-to-vally current rate of the voltage-controlled NDR is larger than 148 and the peak current varies with the increase of collector voltage. The device features high speed and high frequency characteristics derived from HBT and intrinsic bistability and self-latching characteristics due to NDR. A single dual-base HBT can be seen as an integration of NDR device, HBT and photoconductive device. Compared with common HBT,the groove is the key factor producing NDR. 相似文献
3.
基于阈值电压的负温度特性以及热电压的正温度特性,给以适当的权重后把它们相加,提出了一个零温度系数的基准电压电路。该器件由工作在亚阈值区的CMOS晶体管组成,不包含电阻和双极晶体管。采用3支路电流基准结构替代共源共栅结构和嵌入式运算放大器,具有芯片面积小和功耗低的优点。仿真结果表明,在标准0.18μmCMOS工艺下,该电路可在0.75 V电源电压下工作,输出电压为563 mV。在-40~125℃范围内,电压温度系数仅为17.5×10^-6/℃。电源电压范围在1.2~1.8 V时线性灵敏度为569.5×10^-6/V,电源抑制比可达到66.5 dB@100 Hz,最高功耗仅为187.4 nW。 相似文献
4.
针对LED车灯作为多光源发光器件的特点,对于N-1法规和异常电压输入都有着严格的要求。在了解一种简单的三极管电流控制驱动模式的基础上,利用Multisim仿真软件与传统的电阻驱动模式进行功能对比,使电流控制驱动的设计满足车灯安全法规的要求。 相似文献
5.
针对教学中学生常对单管放大电路输入信号幅值与静态工作点对输出波形失真的问题,利用电路分析理论,近似估算了单管共射极放大电路静态工作点对应的参数值,并利用微变信号等效法分析了放大电路的交流特性。利用Multisim软件仿真和硬件实验测试,实验设计让学生更好掌握单管放大电路相关知识。 相似文献
6.
在串联型晶体管稳压电路中,集电极电阻有内部电源和外部电源两种供电方式.定量分析了在电网电压和负载电流发生波动时,不同供电方式对输出电压的影响. 相似文献
7.
在测试了ＡｌＧａＡｓ／ＧａＡｓＨＢＴ（异质结晶体管）的直流特性和Ｓ参数的基础上,建立了其微波小信号等效电路,准确的等效电路有利于其微波线性应用的分析．应用Ｖｏｌｔｅｒａ级数,计算了ＡｌＧａＡｓ／ＧａＡｓＨＢＴ放大器的三阶互调失真,计算结果和双音测试结果相当一致,该ＨＢＴ良好的线性特性证明了其较好的线性应用前景 相似文献
8.
在分析经典Doherty放大器工作原理基础上,对主从放大器使用不同的漏极偏置电压和电路匹配,设计出一种新型Doherty功率放大器,分析了该结构对于效率和线性化的影响.以飞思卡尔公司的MRF6S20010N功放模型,利用ADS2008对放大器进行静态工作点选取,源负载网络匹配和微带线的计算.结果表明这种功率放大器不但能够提高性能指标,还增强了放大器的稳定性. 相似文献
9.
1 Introduction Organic semiconductors are receiving considerableattention due to their remarkable advantages especiallyvarious manufacturing methods ,lowcost and plentifulmaterials .Ebisawa ,et al.[1]fabricated the first poly-mer-based transistor in 1983 . Since then,lots of re-search works have been done in the filed of organicmaterial-based transistors .It was reported that organicthin-fil m transistor ( OTFT) fabricated by usingorganic semiconductor material copper-phthalocyanine(CuPc)[2… 相似文献
10.
在电源主电路中利用三极管集电极-发射极间的等效电阻作为LM317调节端可变电阻,解决了宽范围输出电压源中运算放大器需要较高电压供电的问题,并采用二档自动调节LM317输入电压的方法和电感负载保护电路,降低了故障率;以8位微控制器AT89S52为核心构成串级控制系统,提高了输出电压的响应速度和控制精度;设计了LCD实时显示和键盘、编码器输出电压设定电路,操作方便,减少了操作时间,适应了实验教学需要。 相似文献
11.
The conventional fault analysis method based on symmetrical components supposes that the three-phase parameters of un-transposed transmission line are symmetrical in case of fault. The errors caused by the method with the symmetrical distributed parameter circuit model as the equivalent circuit of the un-transposed ultra high voltage (UHV) transmission line were studied under both normal operation and fault, and the corresponding problems arising were pointed out. By contrast with electromagnetic transient and power electronics (EMTPE) simulation results with the asymmetrical distributed parameter circuit model of un-transposed line, it is shown that the conventional method cannot show the existence of negative and zero sequences before fault happening and there are many errors on voltage and current after fault happening which are different with fault types. The error ranges of voltage and current are 2.13%-81.13% and -7.82%-86.15%, respectively. 相似文献
12.
为分析双极性晶体管放大电路而引入的众多双极性晶体管等效模型加重了初学者负担.本文介绍了一种从双极性晶体管物理结构出发推导出高频低频等效电路以简化分析手段、突出教学目的的教学尝试,同时利用仿真软件的辅助分析加深初学者对工程近似概念的理解. 相似文献
13.
罗青 《南京晓庄学院学报》2010,26(3):27-30
利用广义非线性薛定谔方程,研究了零色散光纤中交叉相位调制不稳定性,分析了高阶色散和高阶非线性系数对增益谱的影响.发现当光脉冲工作在零色散附近时,交叉相位调制不稳定性主要取决于四阶色散,它使增益谱变宽.正五阶非线性使增益谱的谱宽和峰值增大,负五阶非线性使增益谱的谱宽和峰值减小. 相似文献
14.
文章提出了计算三极管放大电路电压放六倍数的新方法──交流等效参数观察法,将画微变等效电路的方法求解简化为观察交流等效参数求解． 相似文献
15.
曾文章 《泉州师范学院学报》2005,23(6):43-47
阐述用高压电脉冲发生器驱动LiNbO3电光偏转器，对激光脉冲进行快速偏转．产生幅度稳定激光脉冲输出的工作原理．分析由冷阴极管、雪崩管和MOS管制成的电脉冲发生器对输出激光脉冲幅度稳定性的实验结果．比较这三种电脉冲发生器对激光脉冲的稳幅作用．发现用雪崩管或MOS管代替进口冷阴极管制成的高压电脉冲发生器，同样获得优良的激光脉冲稳幅的效果．这一结果对于光电器件国产化研究有一定的实际意义． 相似文献
16.
Resonant tunneling diode （RTD） of AlAs/InGaAs/AlAs double barrier-single well structure was designed and fabricated. The devices showed current-voltage characteristics with peak-valley current ratio of 4 ： 1 at room temperature. The scattering parameter of RTD was measured by using an HP8510（C） network analyzer. Equivalent circuit parameters were obtained by curve fitting and optimized. The RTD switching time was estimated using the measured capacitance and average negative differential resistance. The minimum rise time of the sample was estimated to be 21 ps. 相似文献
17.
An accurate circuit of PWM/PFM mode converting and a circuit of auto-adaptively adjusting dimension of power transistor are
described. The duty cycle of the signal when the control mode converts can be gained accurately by using ratios of currents
and capacitances, and an optimal dimension of power transistor is derived with different loads. The converter is designed
by 0.35 μm standard CMOS technology. Simulation results indicate that the converter starts work at 0.8 V input voltage. Combined
with synchronized rectification, the transfer efficiency is higher than 90% with full load range, and achieves 97.5% at rating
output. 相似文献
18.
在建立电压并联反馈电路模型基础上,推导出放大电路中的电压放大倍数、输入电阻、输出电阻的精确计算公式。提出了新的计算方法,从而解决了放大电路计算不方便,精确度不高、准确性不够的问题。进一步揭示了基本放大电路、反馈电路元件参数对反馈放大电路的影响关系。给设计出高性能放大电路及电子仪器指明了方向,同时使电压并联反馈电路的计算更方便。 相似文献
19.
以无源RLC带阻滤波电路为研究对象,建立分数阶新带阻滤波电路模型,研究带阻滤波电路在分数阶域下特性与规律。给出分数阶RLβCα带阻滤波电路阻抗表达式,研究分数阶阶次α、β等系统参数对分数阶滤波电路影响规律,并给出阻抗灵敏度对比分析。此外,分数阶RLβCα带阻滤波电路作为一个重要滤波电路模型,系统分析分数阶阶次α、β等系统参数对截止频率、谐振频率、带宽、品质因数等幅频特性与相频特性影响规律。结果表明,分数阶带阻滤波电路展现出新颖电路特性与优异滤波性能。 相似文献
20.
李京秀 《洛阳工业高等专科学校学报》2001,11(3):25-26
电压增益、输入电阻、输出电阻是放大电路的三项指标，一般用微变等效电路法计算，但是在负反馈放大器中，由于引入反馈支路，用微变等效电路法计算上述指标很困难。本文给出一种消去反馈支路的方法，使负反馈放大器的计算得以简化。 相似文献