共查询到20条相似文献，搜索用时 46 毫秒
1.
2.
Devi CHANDRA ;Judha PURBOLAKSONO ;Yusoff NUKMAN ;Haw-ling LIEW ;Singh RAMESH ;Mohsen-abdel HASSAN 《浙江大学学报(A卷英文版)》2014,15(11):873-882
研究目的：在相同的反复张力下,研究V形切口圆条表面裂纹的疲劳扩展规律。研究方法：1.构建V形切口圆条模型（图1）,基于线性二次元将模型表面离散成一个个网格点（图2）;2.以AZ-6A-T5镁合金为例,利用J积分计算应力强度因数,利用NASGRO裂纹增长率模拟裂纹的疲劳扩展;3.通过研究不同的裂纹纵横比和对应的应力强度因数之间的相关性来研究裂纹的扩展。重要结论：1.在裂纹扩展时裂纹纵横比的初始值对断裂形状的发展有重要影响;2.裂纹纵横比对疲劳负荷寿命的作用比缺口半径更加明显;3.当裂纹前缘演变成一条直线形时可观察到不稳定的裂纹扩展;4.裂纹深度一定时,断裂纵横比越小,疲劳负荷寿命越短;5.当裂纹纵横比为0.6-0.7时,出现了不稳定的裂纹扩展。 相似文献
3.
CUI Hong-bin 《实验室研究与探索》2007,(10)
由于高强度钢在疲劳断裂过程中很难产生辉纹,给裂纹扩展的研究带来一定的困难。本文在对接焊平板的疲劳断裂试验中,采用降载勾线法制造出"海滩状花纹",借此对裂纹扩展过程中裂纹前缘形状和裂纹扩展速率进行分析,并与Newman-Raju公式的计算结果进行比较。 相似文献
4.
The definition ofJ-integral of interfacial crack was introduced.The three.point bending tests were carried out to obtain the criticaI lOading values when the interfacial crack initiation occurred between coatings and substrates.The finite element analysis(FEA)was adopted to analyze the stress distribution in the specimens and compute the J-integral of the interfaciaI crack between LX88A coating and Chinese 0345 steel.The results showed that the average value of critical J-integral iS 0.70 N/m.which can be taken as the fracture parameter to evaluate the interfaciaI fracture behavior for the three-point bending specimens of LX88A coating/Q345 steel system. 相似文献
5.
The definition of J-integral of interfacial crack was introduced. The three-point bending tests were carried out to obtain the critical loading
values when the interfacial crack initiation occurred between coatings and substrates. The finite element analysis (FEA) was
adopted to analyze the stress distribution in the specimens and compute the J-integral of the interfacial crack between LX88A coating and Chinese Q345 steel. The results showed that the average value
of critical J-integral is 0.70 N/m, which can be taken as the fracture parameter to evaluate the interfacial fracture behavior for the
three-point bending specimens of LX88A coating/Q345 steel system.
Supported by Tianjin Natural Science Foundation (No.08JCYBJC09100), New Teacher Research Fund for the Doctoral Program of
Higher Education of China (No.20070056096) and New Century Outstanding Talented Person Plan of China.
XU Lianyong, born in 1975, male, Dr. 相似文献
6.
对调质42CrMo钢进行室温下各种应力循环和对称应变循环的低周疲劳实验,揭示材料的循环软化特性,棘轮变形和低周疲劳特性以及棘轮-疲劳交互作用。结果表明,调质42CrMo钢体现出明显的循环软化;在应力幅值或平均应力较高时,试样的棘轮变形较大,其破坏形式为延性破坏,而在应力水平较低时,材料的破坏由疲劳裂纹扩展所致的脆性断裂引起;材料在应力循环下的低周疲劳寿命由于有棘轮变形的产生而受到平均应力、应力幅值、最大应力和应变比等多种因素的影响。 相似文献
7.
利用2种不同的方法加筋沥青罩面:①在沥青混合料中加入短切玻璃纤维改善沥青混凝土的特性,②采用玻璃格珊加筋沥青混凝土.应用断裂力学方法分析沥青路面裂缝扩展机理.采用沥青混合料设计试验、三点弯曲试验和疲劳裂缝扩展试验,确定加筋沥青混凝土的临界应力强度因子KIC,测量每一种沥青罩面抗裂系统的裂缝扩展速率.本研究的主要特点是提出复合型抗裂罩面系统,分析了多层加筋沥青罩面裂缝扩展过程,推荐了若干沥青路面抗裂系统.结果证明,加筋材料可以提高沥青罩面的抗裂特性,复合型抗裂罩面系统能够有效地阻止反射裂缝的扩展. 相似文献
8.
ＡｃｏｕｓｔｉｃＥｍｉｓｓｉｏｎＭｏｎｉｔｏｒｉｎｇｏｆＦａｔｉｇｕｅＣｒａｃｋＧｒｏｗｔｈｉｎａＳｌｅｎｄｅｒＷｅｂｏｆＢｒｉｄｇｅＧｉｒｄｅｒＹａｎＴｉｎｇｈｕ（颜廷虎）ＺｈｏｎｇＢｉｎｇｌｉｎ（钟秉林）（ＤｅｐａｒｔｍｅｎｔｏｆＭｅｃｈａｎｉｃ... 相似文献
9.
为了分析研究焊缝、热影响区、母材的损伤容限性能差异,对TA15钨极氩弧焊焊缝、热影响区和焊接母材分别进行了断裂韧度试验和疲劳裂纹扩展速率试验,试验结果表明:焊缝、热影响区、焊接母材的断裂韧度值差别不大;三个应力比下(R=0.5,0.06,-1)氩弧焊热影响区裂纹扩展速率均较母材及焊缝的稍高,这种现象在正应力比下的低速扩展区更明显些;焊缝裂纹扩展速率一般稍低于母材。 相似文献
10.
This paper presents a deterministic model to predict the pit evolving morphology and crack initiation life of corrosion fatigue. Based on the semi-ellipsoidal pit assumption, the thermodynamic potential including elastic energy, surface energy and electrochemical energy of the cyclically stressed solid with an evolving pit is established, from which specific parameters that control the pit evolution are introduced and their influence on the pit evolution are evaluated. The critical pit size for crack nucleation is obtained from stress intensity factor criterion and the crack nucleation life is evaluated by Faraday’s law. Meanwhile, this paper presents a numerical example to verify the proposed model and investigate the influence of cyclic load on the corrosion fatigue crack nucleation life. The corrosion pit appears approximately as a hemisphere in its early formation, and it gradually transits from semicircle to ellipsoid. The strain energy accelerates the morphology evolution of the pit, while the surface energy decelerates it. The higher the stress amplitude is, the smaller the critical pit size is and the shorter the crack initiation life is. 相似文献
11.
Based on the nonlinear continuum damage model(CDM) developed by Chaboche,a modified model for high cycle fatigue of TC4 alloy was proposed.Unsymmetrical cycle fatigue tests were conducted on rod specimens at room temperature.Then the material parameters needed in the CDM were obtained by the fatigue tests,and the stress distribution of the specimen was calculated by FE method.Compared with the linear damage model(LDM),the damage results and the life prediction of the CDM show a better agreement with the test and they are more precise than the LDM.By applying the CDM developed in this study to the life prediction of aeroengine blades,it is concluded that the root is the most dangerous region of the whole blade and the shortest life is 58 211 cycles.Finally,the Cox proportional hazard model of survival analysis was applied to the analysis of the fatigue reliability.The Cox model takes the covariates into consideration,which include diameter,weight,mean stress and tensile strength.The result shows that the mean stress is the only factor that accelerates the fracture process. 相似文献
12.
对单点与两点拉剪点焊试样分别进行了疲劳试验,观测了疲劳裂纹的形状和萌生位置,通过动态响应实验测量了疲劳破坏过程中固有频率的变化。对比两种试样的载荷幅寿命关系,认为两点试样的承载能力约为单点试样的两倍。有限分析了两种试样失效时的固有频率比,基于所测量的固有频率,确定了单点与两点试样疲劳失效时的频率比,对比了疲劳过程中的损伤。 相似文献
13.
Through the experiments of 7 T-section composite beams, steel fiber reinforced self-stressing concrete （SFRSC） as the composite beam in the composite layer was studied under the hogging bending. The tests simulated composite layer tensile strain under the hogging bending of inverted loading composite beams, giving the relationship under the different fatigue stress ratios between fatigue cycles and steel bar’s stress range, crack width, stiffness loss and damage, etc., in composite layer. This article established fatigue life equation, and analyzed SFRSC reinforced mechanism to crack width and stiffness loss. The results show that SFRSC as the composite beam concrete has excellent properties of crack resistance and tensile, can reinforce the fatigue crack width and stiffness loss of composite beams, and improve the durability and in normal use of composite beams in the hogging bending zone. 相似文献
14.
Calculation Model of Equivalent Strength for Induced Crack Based on Double-K Fracture Theory and Its Optimizing Setting in RCC Arch Dam 总被引：2，自引：0，他引：2
By means of fracture testing on roller-compacted concrete (RCC) three-point bending beams with two different specimen sizes, the P-CMOD complete curve for RCC was gained. Furthermore, by applying double-K fracture theory, KIC^ini,KIC^un, as well as the critical effective crack length and the critical crack tip opening displacement, were evaluated. Based on the double-K fracture parameters above, the calculation model of equivalent strength for induced crack was established, thus the calculation method on its initiation, stable propagation and unstable fracture was ascertained. Moreover, the finite element simulation analysis of stress field in ShaPai arch dam and the on-site observational splaying points of induced crack at different altitudes validated the reliability of the model. Finally, crack inducer‘s optimal setting in RCC arch dam was studied. It improves the design level of induced crack in RCC arch dam and satisfies the necessity of engineering practice. 相似文献
15.
A newly developed pure rolling fatigue test rig with three contact points for bearing balls was used to perform rolling contact fatigue (RCF) tests. The fatigue properties of GCr15 steel balls and two kinds of Si3N4 ceramic balls (GSN-200 and NBD-200) produced with different technologies were compared. Ball surfaces were examined after failure with optical microscope and scanning electron microscope (SEM). It was identified by tests that the failure mode of ceramic balls was surface spall. The main factor of ceramic ball failure was principal tensile stress. Life tests data, summarized in accordance with the Weibull theory, showed that the life of GSN-200 balls was close to that of GCr15 balls, whereas the life of NBD-200balls was much longer than those of GSN-200 and GCr15. Under the same working condition, the temperature rise of all ceramic balls was lower than that of steel balls, and their crack propagation rates were slower than that of steel balls. 相似文献
16.
The mechanism and criterion of crack initiation and propagation of rocks were investigated by many researchers,And the creep behaviour of rocks was also theoretically and experimentally studied by some scientists and engineers.The characteristics of crack initation and propagation of rocks under creep condition.however,are very improtant for rock engineering and still not paid enough attention by researchers,In this paper,the criterion and mechanism of crack initiation and propagation under creep condition were investigated using specimens collected from sandstone rock formations outcropping in the Emei Mountain,the Sichuan Province of China.Cuboid specimens under three point bending were used in this investigation.All specimens were classified into four sorts and used for Mode-I fracutre of creep frcture tests.The experimental result shows that due to creep deformation.rock crack will inevitably initialt and propagate under a load of KI,which is less than fracture toughness KIC but not less than a constant(marked as KIC2),KIC2 indicates the ability of rock to resist crack initiation and propagation under creep conditions and is less than fracture tough ness KIC.defined as creep fracture toughness in this paper,KIC2 should be considered as an importnat parameter on design and computation of rock engineering.The microstructureal mechanism for crack initiation and propagation of rock materials under creep condition was introduced based on competitive model between softening effect and hardening effect,and the validity of test result was explained.The test result was also verified in rheological theory.When KI is more than KIC2 but less than KIC,rock crack will initiate and propagate after a time interval of sustained loading under creep condition.In order to find the relation between duration of sustained lading.which can lead to crack initiation and propagation,and the initial stress intensity factor KI,an unequal0interval time sequence forecasting and predicting model was introduced,and the relation was obtained for homogeneous and isotropic fine-grained red sandstone.Finally a modified fracture toughness formula was given,in which the influence of fracture process zone(FPZ) was fully considered. 相似文献
17.
对TC4钛合金试样拉伸疲劳断裂宏观试验结果、相应的断口和卸载表面观察分析研究,发现在试样断口上有明显的河流花纹走向、韧窝和韧性条带特征.其断裂机理是疲劳拉伸载荷作用下,在应力值比较高时一些沿层裂纹开始出现并扩展,同时微孔长大形成韧窝,并最后导致了材料断裂. 相似文献
18.
复杂飞机结构裂纹萌生寿命确定的工程方法 总被引：1，自引：0，他引：1
采用静拉伸应变测量试验的方法,确定了典型飞机复杂结构在载荷作用下的应变分布,并准确判断出其疲劳危险部位。对典型飞机复杂结构模拟件进行了等幅加载疲劳试验,并在疲劳试验过程中采用着色探伤方法测得了疲劳裂纹扩展数据。在此基础上,提出并建立了一种适用于确定复杂结构疲劳裂纹萌生寿命的工程方法,包括疲劳裂纹萌生寿命反推法和含有不确定寿命样本的统计推断方法。根据该方法对试验样本疲劳数据进行处理得出了裂纹萌生中值寿命及其在95%置信水平下的单侧置信下限。 相似文献
19.
The fracture behavior of a ceramic reinforced metal-base coating prepared by high velocity arc spraying (HVAS)technology in three-point bending test was studied.Moreover,finite element analysis(FEA)was adopted to analyze the stress distribution in the crack front.It can be found that the crack norrnal to the interface in the coatings occurred at the location where a fixed moment of force was reached.So the critical moment can be taken as thecoating cracking criterion,which was confirmed by FEA results.In addition,the stress levels at three different locations where cracks occurred near the interface are almost the same.The results will provide reference for the design of coatings and the structure integrity evaluation of coating/substrate systems. 相似文献
20.
A problem for a central crack in a plate subjected to plane strain conditions is investigated.Mode Ⅰ crack loading is created by a dynamic pressure pulse applied at a large distance from the crack.It was found that for a certain combination of amplitude and duration of the pulse applied,the energy transmitted to the sample has a strongly marked minimum,meaning that with the pulse amplitude or duration moving away from the optimal values,minimum energy required for initiation of crack growth increases rapidly.The results obtained indicate a possibility to optimise energy consumption of different industrial processes connected with fracture.Much could be gained in,for example,drilling or rock pounding where energy input accounts for the largest part of the process cost.Presumably further investigation of the effect observed can make it possible to predict optimal energy saving parameters,i.e.frequency and amplitude of impacts,for industrial devices,e.g.bores,grinding machines,and hence significantly reduce the process cost.The prediction can be given based on the parameters of the media fractured (material parameters,prevalent crack length and orientation,etc.). 相似文献