共查询到20条相似文献，搜索用时 968 毫秒
1.
The dynamic characteristics and failure modes of steel reinforced concrete (SRC) columns subjected to blast loading are complicated because of the transient stress wave in the SRC columns and the interaction between steel and concrete. This paper presents a numerical simulation of the response of SRC columns subjected to blast loading using hydrocode LS-DYNA. In the numerical model, a sophisticate concrete material model (the Concrete Damage Model) is employed with consideration of the strain rate effect and the damage accumulation. An erosion technique is adopted to model the spalling process of concrete. The possible failure modes of SRC columns are evaluated. It is observed that the failure of SRC columns subjected to blast load can generally be classified into three modes, namely, a direct failure in concrete body due to the stress wave, a transverse shear failure near the support sections due to the high shear force, and a flexural failure pertaining to large local and global deformation of the reinforcing steel. 相似文献
2.
Terrorist attacks using improvised explosive devices (lED) can result in unreinforced masonry (URM) wall collapse.Protecting URM wall from lED attack is very complicated.An effective solution to mitigate blast effects on URM wall is to retrofit URM walls with metallic foam sheets to absorb blast energy.However,mitigation of blast effects on metallic foam protected URM walls is currently in their infancy in the world.In this palaer,numerical models are used to simulate the performance of aluminum foam protected URM walls subjected to blast loads.A distinctive model,in which mortar and brick units of masonry are discritized individually,is used to model the performance of masonry and the contact between the masonry and steel face-sheet of aluminum foam is modelled using the interface element model.The aluminum foam is modelled by a nonlinear elastoplastic material model.The material models for masonry,aluminum foam and interface are then coded into a finite element program LS-DYNA3D to perform the numerical calculations of response and damage of aluminum foam protected URM walls under airblast loads.Discussion is made on the effectiveness of the aluminum foam protected system for URM wall against blast loads. 相似文献
3.
Terrorist attacks using improvised explosive devices (IED) can result in unreinforced ma-sonry (URM) wall collapse. Protecting URM wall from IED attack is very complicated. An effective solution to mitigate blast effects on URM wall is to retrofit URM walls with metallic foam sheets to absorb blast energy. However, mitigation of blast effects on metallic foam protected URM walls is currently in their infancy in the world. In this paper, numerical models are used to simulate the per-formance of aluminum foam protected URM walls subjected to blast loads. A distinctive model, in which mortar and brick units of masonry are discritized individually, is used to model the perform-ance of masonry and the contact between the masonry and steel face-sheet of aluminum foam is modelled using the interface element model. The aluminum foam is modelled by a nonlinear elas-toplastic material model. The material models for masonry, aluminum foam and interface are then coded into a finite element program LS-DYNA3D to perform the numerical calculations of response and damage of aluminum foam protected URM walls under airblast loads. Discussion is made on the effectiveness of the aluminum foam protected system for URM wall against blast loads. 相似文献
4.
GONG Shunfeng LU Yong GAO Feng JIN Weiliang 《天津大学学报(英文版)》2006,12(B09):248-253
For a building structure subjected to impulsive loading, particularly shock and impact loading, the response of the critical columns is crucial to the behaviour of the entire system during and after the blast loading phase. Therefore, an appropriate evaluation of the column response and damage under short-duration impulsive loading is important in a comprehensive assessment of the performance of a building system. This paper reports a dynamic analysis approach for the response of RC columns subjected to impulsive loading. Considering that the dynamic response of a column in a frame structure can also be affected by the floor movement which relates to the global vibration of the frame system, a generic column-mass model is used, in which a concentrated mass is attached to the column top to simulate the effect of a global vibration. To take into account the high shear effect under impulsive load, the model is formulated using Timoshenko beam theory, and three main nonlinear mechanisms are considered. Two typical scenarios, one under a direct air blast loading, and another under a blast-induced ground excitation, are analyzed and the primary response features are highlighted. 相似文献
5.
For a building structure subjected to impulsive loading, particularly shock and impact loading , the response of the critical columns is crucial to the behaviour of the entire system during and after the blast loading phase. Therefore, an appropriate evaluation of the column response and damage under short-duration impulsive loading is important in a comprehensive assessment of the performance of a building system. This paper reports a dynamic analysis approach for the response of RC columns subjected to impulsive loading. Considering that the dynamic response of a column in a frame structure can also be affected by the floor movement which relates to the global vibration of the frame system, a generic column-mass model is used, in which a concentrated mass is attached to the column top to simulate the effect of a global vibration. To take into account the high shear effect under impulsive load, the model is formulated using Timoshenko beam theory, and three main nonlinear mechanisms are considered. Two typical scenarios, one under a direct air blast loading, and another under a blast-induced ground excitation, are analyzed and the primary response features are highlighted. 相似文献
6.
Numerical Simulation of Dynamic Response and Collapse for Steel Frame Structures Subjected to Blast Load 总被引：4，自引：0，他引：4
The progressive collapse of steel frame structures under the blast load was investigated using LS-DYNA. The multi-material Eulerian and Lagrangian coupling algorithm was adopted. A flu-id-structure coupling finite element model was established which consists of Lagrange element for simulating steel frame structures and concrete ground, multiple ALE element for simulating air and TNT explosive material. Numerical simulations of the blast pressure wave propagation, struc-tural dynamic responses and deformation, and progressive collapse of a five-story steel frame structure in the event of an explosion near above ground were performed. The numerical analysis showed that the Lagrangian and Eulerian coupling algorithm gave good simulations of the shock wave propagation in the mediums and blast load effects on the structure. The columns subjected to blast load may collapse by shear yielding rather than by flexural deformation. The columns and joints of steel beam to column in the front steel frame structure generated enormous plastic defor-mation subjected to intensive blast waves, and columns lost carrying capacity, subsequently lead-ing to the collapse of the whole structure. The approach coupling influence between struc-tural deformation and fluid load well simulated the progressive collapse process of structures, and provided an effective tool for analyzing the collapse mechanism of the steel frame structure under blast load. 相似文献
7.
The progressive collapse of steel frame structures under the blast load was investigated using LS-DYNA.The multi-material Eulerian and Lagrangian coupling algorithm was adopted.A fluid-structure coupling finite element model was established which consists of Lagrange element for simulating steel frame structures and concrete ground,multiple ALE element for simulating air and TNT explosive material.Numerical simulations of the blast pressure wave propagation,structural dynamic responses and deformation,and progressive collapse of a five-story steel frame structure in the event of an explosion near above ground were performed.The numerical analysis showed that the Lagrangian and Eulerian coupling algorithm gave good simulations of the shock wave propagation in the mediums and blast load effects on the structure.The columns subjected to blast load may collapse by shear yielding rather than by flexural deformation.The columns and joints of steel beam to column in the front steel frame structure generated enormous plastic deformation subjected to intensive blast waves,and columns lost carrying capacity,subsequently leading to the collapse of the whole structure.The approach coupling influence between structural deformation and fluid load well simulated the progressive collapse process of structures,and provided an effective tool for analyzing the collapse mechanism of the steel frame structure under blast load. 相似文献
8.
Current practice in analysis and design of blast doors subjected to blast loading considers only simple boundary conditions and material properties. The boundary conditions and material properties, in fact, have considerable influence on the response of blast doors subjected to blast loading. In this paper, the dynamic responses of a reinforced concrete arched blast door under blast loading were analyzed by the finite element program ABAQUS, combined with a previously developed elasto-viscoplastic rate-sensitive material model. And the effect of the surrounding rock mass and contact effect of the doorframe were also taken into account in the simulation. It is demonstrated that the strain-rate effect has considerable influence on the response of reinforced concrete blast door subjected to blast loading and must be taken into account in the analysis. 相似文献
9.
The blast resistance of structures used in buildings needs to be investigated due to the increased threat of a terrorist attack. The damage done by Composition B or Powergel to steel fibre reinforced reactive powder concrete (SFRPC) panels and ordinary reinforced concrete (RC) panels of equivalent static flexural strength is compared. A 0.5 kg charge was detonated at a distance of 0.1 m from the 1.3 m×1.0 m×0. 1 m (thick) panels, which were simply supported and spaning 1.3m. Dynamic displacement measurements, high-speed video recording and visual examination of the panels for spall and breach were undertaken. The SFRPC panels withstood the bare charge blast better than the reinforced ordinary concrete panels. Neither type of panel was breached using a 0.5 kg charge. The RC panel exhibited more spalling when Composition B was used. Under successive Composition B loading conditions, the RC panel was breached. In comparison the SFRPC panel was not breached. Exposure to fragmenting charge loading conditions confirmed these performance differences between the SFRPC panel and the reinforced ordinary concrete panel. 相似文献
10.
Under extreme loading condition,a shelter will provide a safe place to protect people from injury caused by blast wave and fragments.In order to save resource and reuse waste materi-als,a new design concept for blast protection shelter was explored.The new construction was composed of I-section steel panel or C-channel steel panel filled with recycled concrete aggregate.The compaction process of the recycled concrete aggregate filled in the steel construction was ex-perimentally investigated.A single storey shelter based on the proposed design concept was nu-merically simulated by using LS-DYNA software.In the 3D numerical model,three walls were de-signed using I-section steel and one wall using C-channel steel,and all of the four walls were filled with recycled concrete aggregate.The penetration analysis was done by using ConWep.Some penetration tests were also carried out by using a gas gun.It is found that the proposed shelter based on the design concept is effective for blast protection. 相似文献
11.
12.
以跨度为120m的刚性拱肋柔性系杆的下承式钢管混凝土拱桥为分析模型,利用摩擦摆减震隔震支座对简支体系的桥跨结构进行减震研究,运用MIDAS有限元软件模拟多维人工地震波输入以检验摩擦摆系统的减震效果。分析结果证明了在大跨度钢管混凝土拱桥中应用摩擦摆隔震支座系统的有效性。 相似文献
13.
Retrofitting of RC Slabs Against Explosive Loads 总被引：1，自引：0，他引：1
OEHLERS Deric John 《天津大学学报(英文版)》2006,12(Z1)
With the increase of terrorist bomb attacks on buildings, there is a need to develop advanced retrofitting techniques to strengthen structures against blast loads. Currently, several guidelines including an Australian version for retrofitting reinforced concrete (RC) structures are available for the design of retrofitting systems against seismic and monotonic loads using steel or fibre reinforced polymer (FRP) plates that can be either adhesively bonded to the surface or near surface mounted to the concrete cover. However, none of these guidelines provide advice suitable for retrofitting structures subjected to blast loads. In this paper, numerical models are used to simulate the performance of retrofitted RC slabs subjected to blast loads. Airblast pressure distributions on the surface of the slabs estimated in a previous study are used as input in the analysis. A material damage model developed previously for concrete and an elastoplastic model for steel bars are employed in this research for modelling reinforced concrete behaviour due to explosive loads. The material models and blast loading are coded into a finite element computer program LS-DYNA3D to do the analysis. With the numerical model, parametric studies are conducted to investigate RC slabs retrofitted by either externally bonded or near-surface mounted plates or GFRP sheets subjected to blast loads. Discussion is made on the effectiveness of the retrofitting system for RC slabs against blast loads. 相似文献
14.
Surface contact explosion experiments have been performed for the study of dynamic response of the hard-soft-hard sandwich panel under blast loading. Experimental results have shown that there are four damage modes, including explosion cratering, scabbing of the backside, radial cracking induced failure and circumferential cracking induced failure. It also illustrates that the foam material sandwiched in the multi-layered media has an important effect on damage patterns. The phenomena encountered have been analyzed by the calculation with ALE method. Meanwhile, the optimal analysis of foam material thickness and position in the sandwich panel were performed in terms of experimental and numerical analysis. The proper thickness proportion of the soft layer is about 20% to the thickness of sandwich panel and the thickness of the upper hard layer and lower hard layer is in the ratio of 7 to 3 under the condition in this paper when the total thickness of soft layer remains constant. 相似文献
15.
1 Ｉｎｔｒｏｄｕｃｔｉｏｎ Ｔｈｅｓｕｒｆａｃｅｔｅｘｔｕｒｅｓｔｅｅｌｓｈｅｅｔｓｈａｖｅｂｅｅｎｅｘｔｅｎｓｉｖｅｌｙｕｓｅｄｉｎａｕｔｏｍｏｂｉｌｅｉｎｄｕｓｔｒｙｆｏｒｔｈｅｉｒｇｏｏｄｆｏｒｍａｂｉｌｉｔｙａｎｄｐａｉｎｔｉｎｇｐｅｒｆｏｒｍａｎｃｅ.Ａｓｋｎｏｗｎ,ｔｈｅｒｅｅｘｉｓｔｅｓｆｒｉｃｔｉｏｎｂｅｔｗｅｅｎｔｈｅｓｈｅｅｔａｎｄｍｏｄｅｌｄｕｒｉｎｇｓｔａｍｐｉｎｇ.Ｗｈｅｎｔｈｅｓｈｅｅｔｉｓｄｅｆｏｒｍｅｄｉｎｔｏａｗｏｒｋｐｉｅｃｅ,ｔｈｅｐｒｏｃｅｓｓｏｆｓｈｅｅｔ… 相似文献
16.
In Order to reduce economic and life losses due to terrorism or accidental explosion threats,reinforced concrete(RC)slabs of buildings need to be designed or retrofitted to resist blast loading.In this paper the dynamic behavior Of RC slabs under blast loading and its influencing factors are studied.The numerical model of an RC slab subjected to blast loading is established using the explicit dynamic analysis software.Both the strain rate effect and the damage accumulation are taken into account in the material model.The dynamic responses of the RC slab subiected to blast loading are analyzed,and the influence of concrete strength,thickness and reinforcement ratio on the behavior of the RC slab under blast loading iS numerically investigated.Based on the numerical results.some principles for blast-resistant design and retrofitting are proposed to improve the behavior of the RC slab subjected to blast loading. 相似文献
17.
Dong-ming Yan Hua-wei Yin Cheng-lin Wu Yan-long Li Jason Baird Gen-da Chen 《浙江大学学报(A卷英文版)》2016,17(9):689-701
In this study, two full-size concrete walls were tested and analyzed to demonstrate the effectiveness of a chemically reactive enamel (CRE) coating in improving their mechanical behavior under blast loading: one with CRE-coated rebar and the other with uncoated rebar. Each wall was subjected in sequence to four explosive loads with equivalent 2, 4, 6-trinitrotoluene (TNT) charge weights of 1.82, 4.54, 13.6, and 20.4 kg. A finite element model of each wall under a close-in blast load was developed and validated with pressure and strain measurements, and used to predict rebar stresses and concrete surface strain distributions of the wall. The test results and visual inspections consistently indicated that, compared with the barrier wall with uncoated reinforcement, the wall with CRE-coated rebar has fewer concrete cracks on the front and back faces, more effective stress transfers from concrete to steel rebar, and stronger connections with its concrete base. The concrete surface strain distributions predicted by the model under various loading conditions are in good agreement with the crack patterns observed during the tests. 相似文献
18.
LI Xiudi ZHENG Yingren 《天津大学学报(英文版)》2006,12(B09):177-181
In order to define the loading on protective doors of an underground tunnel, the exact knowledge of the blast propagation through tunnels is needed. Thirty-three scale high-explosive tests are conducted to obtain in-tunnel blast pressure for detonations external, internal and at the tunnel entrance. The cross section of the concrete model tunnel is 0.67 m^2. Explosive charges of TNT, ranging in mass from 400 g to 4 600 g, are detonated at various positions along the central axis of the model tunnel. Blast gages are flush-installed in the interior surface of the tunnel to record side-on blast pressure as it propagates down the tunnel. The engineering empirical formulas for predicting blast peak pressure are evaluated, and are found to be reasonably accurate for in-tunnel pressure prediction. 相似文献
19.
In order to define the loading on protective doors of an underground tunnel, the exact knowledge of the blast propagation through tunnels is needed. Thirty-three scale high-explosive tests are conducted to obtain in-tunnel blast pressure for detonations external, internal and at the tunnel entrance. The cross section of the concrete model tunnel is 0.67 m2. Explosive charges of TNT, ranging in mass from 400 g to 4 600 g, are detonated at various positions along the central axis of the model tunnel. Blast gages are flush-installed in the interior surface of the tunnel to record side-on blast pressure as it propagates down the tunnel. The engineering empirical formulas for predicting blast peak pressure are evaluated, and are found to be reasonably accurate for in-tunnel pressure prediction. 相似文献
20.
为了研究钢筋增强ECC梁受弯性能,进行了钢筋增强ECC梁和普通钢筋混凝土梁受弯的对比研究.结果表明,相比普通钢筋混凝土梁,钢筋增强ECC梁的受弯承载力和延性分别提高了24.8%和187.76%,并且在梁中用ECC代替混凝土可有效延缓裂缝的发展.此外,采用简化的ECC本构模型对钢筋增强ECC及混凝土梁的受弯性能进行了非线性有限元分析,模拟结果与试验结果吻合较好,在服役期间钢筋增强ECC梁的裂缝可以控制在0.4 mm以下.ECC材料的使用可明显提高梁的抗弯承载力、变形能力、延性等受弯性能. 相似文献