共查询到19条相似文献，搜索用时 187 毫秒
1.
2.
杨惠山 《泉州师范学院学报》2008,26(2):44-48
制备一种利用4,4’,4＂-tris（3-methylphenylphenylamino）-triphenylamine（m—MTDATA）作为空穴注入缓冲层的器件．m—MTDATA增加部分从阳极ITO注入到有机层NPB的空穴,从而平衡了空穴和电子的注入．有缓冲层的有机发光器件比没有缓冲层有机发光器件的电流效率有了明显的提高．当缓冲层m-MTDA—TA为25nm时,最大电流效率在7V时达到3．15cd／A．是没有缓冲层器件电流效率的近3．5倍． 相似文献
3.
《佳木斯教育学院学报》2017,(1)
制备结构为ITO/Mo O3(7nm)/NPB(40nm)/MCP:Fir6(30nm:8%)/MCP:Ir(piq)acac(3nm:1%)/Bphen(40nm)/Cd S(x nm)/Li F(0.5nm)/Al(100nm)的有机电致发光器件。在常温下研究了Cd S薄层对器件发光性能的影响。相同电压下,具有Cd S薄层结构的器件电流密度明显提高,最大电流效率为14.81 cd/A(6V),最大亮度为8947 cd/m2,对应器件效率为3.93 cd/A。 相似文献
4.
基于密度泛函理论结合非平衡格林函数方法对5个Al原子构成的链耦合在两半无限Au（100）电极之间形成三明治结构的纳米结点的电导进行了第一性原理计算．结果得到电导随两极距离的变化关系,当两极距离为22．116A时,体系总能量最低,几何结构最稳定,此时电导为0．596C0（G0=2e^2／h）,电子主要通过Al链原子的P电子轨道进行传输;而当电极距离为24．116 A时,电导最大,其值为2．156G0．结果表明Al链的稳定结构并不是电子输运的最佳结构． 相似文献
5.
6.
作者以黄淮海平原典型的小麦玉米两熟农作制为案例，进行了水氮耦合试验。结果表明，在同一施氮水平上，麦玉产量随着灌水量增加而增加，灌2水比灌1水，产量增加幅度是2．60％～14．45％，浇水3次的麦玉产量与灌水2次的基本持平或略有下降。因此，以小麦灌2水处理最好；在同一水处理上，麦玉产量随着施氮量的增加而增加，当施氮量增加到22．5kg／667m^2时产量达到最高，施氮水平增加到30．kg／667m^2时，有所下降。因此，以单位耕地施氮22．5kg／667m^2最佳。水分利用效率与麦玉产量具有相同的变化趋势。所以，以小麦灌2水，单位耕地施氮22．5kg／667m^2时作物产量和水分利用效率最好，此时对小麦而言可节水50m^3／667m^2左右。 相似文献
7.
苗壮 《赤峰学院学报(自然科学版)》2013,(19):32-34
本文在和田地区于田县,设计5892m3／hm^2、6714m^2／hm^2、7916m^3／hm^2、9353m^3／hm^2等四个灌水定额,针对滴灌葡萄进行试验研究,主要研究土壤水分分布规律、葡萄耗水规律以及葡萄的产量和水分利用效率,并对数据进行回归分析．研究表明：当灌水定额为573m^2／hm^2时葡萄一行两管布置模式土壤剖面含水量分布最优;葡萄的耗水高峰在果实膨大期,日均耗水量都在15mm左右．灌水量为5892m3／hm2时葡萄受到明显的水分胁迫,葡萄生育期提前．灌水量7916m^3／hm^2时葡萄产量最大,达到18450kg／hm^2且葡萄水分生产效率最大,回归分析分析表明当灌水量为8727．5m^3／hm^2时．葡萄产量最高．研究结论可以为极端干旱区葡萄节水灌溉提供技术支持． 相似文献
8.
9.
原题 在国家政策的宏观调控下,某市的商品房成交价由今年3月份的14000元／m^2下降到5月份的12600元／m^2． 相似文献
10.
采用喹啉氮杂环类铱配合物[（PPQ）2Ir（acac）]为客体,以聚芴和2-（4-二苯基）-5-（4-叔丁基苯基）-1,3,4-噁二唑（PBD）为主体,研究了红光磷光有机电致发光的性质.样品的吸收光谱和发射光谱的结果表明（PPQ）2Ir（acac）和聚芴掺杂体系可以发生从主体到客体的有效Fo¨rster能量转移.然而,器件的电致发光光谱与样品的光致发光谱出现了明显的不同.在相同掺杂浓度下,前者更能实现纯的红光发射.这个结果表明,除了能量转移之外,客体的电荷捕获也是实现器件红色发光的原因之一.当（PPQ）2Ir（acac）掺杂浓度为1.0 wt%时,我们在10 V工作电压下得到了发光亮度为1 792 cd/m2,发光效率为6.16 cd/A的高性能红光器件. 相似文献
11.
In order to compare two kinds of blue electroluminescent materials,we have investigated two kinds of blue OLEDs with the similar structure ITO/CuPc/NPB/JBEM:perylene/Alq/Mg:Ag[device(J)] and ITO/CuPc/NPB/DPVBi:perylene/Alq/Mg:Ag[device(D)].The difference of luminance and efficiency was not obvious for the two devices,However,there was remarkable difference for their lifetime.The device(J) achieved longer half lifetime of 1035h at initial luminance of 100 cd/m^2,and that of device(D) was only255h,According to their energy level diagrams,the differentce of their stability may originate from different host materials in the two devices.It may be attributed to the better thermal stability of JBEM molecues than that of DPVBi.It is shown that JBEM may be a promising blue organic electroluminescent material with great stability. 相似文献
12.
金属Yb兼具功函数低、透光度高和化学稳定性相对较高等优点,非常适合作为有机顶部发光器件(TEOLED)的透明阴极材料。计算表明:TEOLED阴极层中加入金属Yb可以有效地抑制器件工作过程中产生的表面等离子体激元振荡(SPs),从而提高器件的相关性能。本文比较性地研究了两种阴极层不同(Yb/Yb:Au和Yb/Yb:Ag)、结构相同(ITO/NPB/Alq3/阴极)的TEOLED。结果表明,直接利用Yb:Au或Yb:Ag共沉积层作为透明阴极的TEOLED的透光度很高,但其电子注入能力较差、发光效率较低;而在Yb:Ag(或Yb:Au)共沉积层和Alq3层之间插入厚度适当的Yb层后,虽然透光度略有下降,但其发光效率得到了显著的提高。 相似文献
13.
Three types of blue-violet light-emitting devices based on an exciton-confined structure have been prepared, in which different materials were used as emitting layers and hole-transporting layers. They had structures of ITO/CuPc/NPB/CPB/TPBi/Alq3/LiF/Al(DNC), ITO/CuPc/JO3/CBP/TPBi/Alq3/LiF/Al(DJC ) and ITO/CuPc/JO3/FNPD/TPBi/Alq3/LiF/Al(DJF). Here copper phthalocyanine (CuPc) acted as hole-injecting layer( HIL), N, N-bis-(1-naphthyl)-N, N-diphenyl-1. lbiphenyl-4-4-diamine(NPB) and J03 bole-transporting layers ( HTLs), 4,4‘-dicarbazolyl-1,1‘ -biphenyl (CBP) and FNPD as emitting layers( EMLs), N, arylbenzimidazoles (TPBi) as holeblocking layer ( HBL ), and tris(8-quinolinolato ) aluminium complex ( Alq3 ) as electron- transporting layer ( ETL). TPBi applied here is a good confinement to both charges and excitons, which make the devices emit blue-violet light originating from the emitter, CBP and FNPD. Their characteristics have also been investigated. The result shows that the device DNC based on NPB/CBP has the best performance among the three devices. The excellence of DNC is attributed to the better hole-transporting ability of NPB as compared with J03, and the better emitting ability of CBP as compared with FNPD, although the best matching of energy levels is found in the hole-transporting layer and emitting layer of the device DJP. 相似文献
14.
陈知新谢文明 《福建工程学院学报》2020,(6):587-592
利用红、绿、蓝三基色量子点材料作为发光层,使用旋涂法实现了3 种颜色的量子点发光二极管的制备。选择合适材料和溶剂形成各功能层薄膜,通过改变量子点溶液的浓度来调控器件的光电性能。对不同浓度下的量子点溶液制备的三色器件进行测试和比较,得到3 种颜色量子点溶液的合适浓度,使最终制备的三基色发光器件具有相同的制备工艺和相当的发光亮度,其亮度均可达到104cd/ m2的量级,为后续使用喷墨打印法来实现三基色QLED 提供理论和实践基础。 相似文献
15.
In the current studies a miniature silicon wafer fuel cell （FC） using L-ascorbic acid as fuel was developed. The cell employs L-ascorbic acid and air as reactants and a thin polymer electrolyte as a separator. Inductively coupled plasma （ICP） silicon etching was employed to fabricate high aspect-ratio columns on the silicon substrate to increase the surface area. A thin platinum layer deposited directly on the silicon surface by the sputtering was used as the catalyst layer for L-ascorbic acid electro-oxidation. Cyclic voltammetry shows that the oxidation of L-ascorbic acid on the sputtered platinum layer is irreversible and that the onset potentials for the oxidation of L-ascorbic acid are from 0.27 V to 0.35 V versus an Ag/AgCl reference electrode. It is found that at the room temperature, with 1 mol/L L-ascorbic acid/PBS （phosphate buffered solution） solution pumped to the anode at 1 ml/min flow rate and air spontaneously diffusing to the cathode as the oxidant, the maximum output power density of the cell was 1.95 mW/cm^2 at a current density of 10 mA/cm^2. 相似文献
16.
低电流密度电解金属钕研究 总被引：6，自引：0，他引：6
本文首次介绍了氟化物熔盐体系中在低阴极、阳极电流密度条件下电解制备稀土金属钕的研究情况.结果表明在阴极电流密度为1.39 A/cm2情况下,电解制备金属钕获得了极高的阴极电流效率,且电解电压仅4.8V左右.该研究为下埋阴极稀土金属熔盐电解槽的研究和设计提供了坚实的理论基础.用数据拟合法得到了电解电压与阴极和阳极电流密度之间以及电流效率与阴极电流密度之间的数学关系式. 相似文献
17.
采用真空热蒸镀法,以热活化延迟荧光(TADF)材料为主体材料、发光材料为客体材料制备混合薄膜发光层,以提高蓝色荧光材料的OLED发光效率。当OLED器件结构为ITO/HAT-CN(5 nm)/TAPC(30 nm)/TCTA(10 nm)/Blue-Or:DMAC-DPS(30%,30 nm)/DPEPO(10 nm)/Bphen(30 nm)/LiF(1 nm)/Al(70 nm)时,器件的光电性能最佳。此蓝光TADF-OLED器件的外量子效率为12.39%,电流效率为21.68 cd/A,功率效率为19.44 lm/W。研究发现改变TADF-OLED的掺杂主体材料和添加空穴注入层均可有效地提高器件的光电特性。实验内容与该领域的前沿科学研究相结合,OLED器件的光电性能稳定、实验现象显著,适于引入本科实验课程。通过该综合实验学生可以夯实实验基础、了解研究热点、掌握最新的科研动态。 相似文献
18.
19.
Two types of molecular and polymer devices employing (2-(4′-biphenyl)-5-(4““““““““-tert-butylphenyl)-1,3,4-oxadiazole) (PBD)and poly(N-vinylcarbazole) (PVK) as electron transport and hole transport materials, respectively, have been fabricated. The structures of these two devices are ITO/PVK( 70 nm)/PBD(60 nm)/A1 and ITO/PVK: PBD (1:1 by mass, 70 nm)/A1. The formation of exciplex is evident by comparing the electroluminescence (EL) of a bi-layer device and the photoluminescence (PL) of a PVK and PBD mixed film.The maximum emission energy of exciplex evaluated is consistent with the peak emission of EL. Blue emissions from both devices are obtained. The type of exicplex is interpreted based on the energy level diagram of the bi-layer device. 相似文献