共查询到20条相似文献，搜索用时 453 毫秒
1.
In Order to reduce economic and life losses due to terrorism or accidental explosion threats,reinforced concrete(RC)slabs of buildings need to be designed or retrofitted to resist blast loading.In this paper the dynamic behavior Of RC slabs under blast loading and its influencing factors are studied.The numerical model of an RC slab subjected to blast loading is established using the explicit dynamic analysis software.Both the strain rate effect and the damage accumulation are taken into account in the material model.The dynamic responses of the RC slab subiected to blast loading are analyzed,and the influence of concrete strength,thickness and reinforcement ratio on the behavior of the RC slab under blast loading iS numerically investigated.Based on the numerical results.some principles for blast-resistant design and retrofitting are proposed to improve the behavior of the RC slab subjected to blast loading. 相似文献
2.
Retrofitting of RC Slabs Against Explosive Loads 总被引：1，自引：0，他引：1
OEHLERS Deric John 《天津大学学报(英文版)》2006,12(Z1)
With the increase of terrorist bomb attacks on buildings, there is a need to develop advanced retrofitting techniques to strengthen structures against blast loads. Currently, several guidelines including an Australian version for retrofitting reinforced concrete (RC) structures are available for the design of retrofitting systems against seismic and monotonic loads using steel or fibre reinforced polymer (FRP) plates that can be either adhesively bonded to the surface or near surface mounted to the concrete cover. However, none of these guidelines provide advice suitable for retrofitting structures subjected to blast loads. In this paper, numerical models are used to simulate the performance of retrofitted RC slabs subjected to blast loads. Airblast pressure distributions on the surface of the slabs estimated in a previous study are used as input in the analysis. A material damage model developed previously for concrete and an elastoplastic model for steel bars are employed in this research for modelling reinforced concrete behaviour due to explosive loads. The material models and blast loading are coded into a finite element computer program LS-DYNA3D to do the analysis. With the numerical model, parametric studies are conducted to investigate RC slabs retrofitted by either externally bonded or near-surface mounted plates or GFRP sheets subjected to blast loads. Discussion is made on the effectiveness of the retrofitting system for RC slabs against blast loads. 相似文献
3.
The dynamic characteristics and failure modes of steel reinforced concrete (SRC) columns subjected to blast loading are complicated because of the transient stress wave in the SRC columns and the interaction between steel and concrete. This paper presents a numerical simulation of the response of SRC columns subjected to blast loading using hydrocode LS-DYNA. In the numerical model, a sophisticate concrete material model (the Concrete Damage Model) is employed with consideration of the strain rate effect and the damage accumulation. An erosion technique is adopted to model the spalling process of concrete. The possible failure modes of SRC columns are evaluated. It is observed that the failure of SRC columns subjected to blast load can generally be classified into three modes, namely, a direct failure in concrete body due to the stress wave, a transverse shear failure near the support sections due to the high shear force, and a flexural failure pertaining to large local and global deformation of the reinforcing steel. 相似文献
4.
DEEKS Andrew 《天津大学学报(英文版)》2006,12(Z1)
To model the damage process of masonry walls under blast loading, a dynamic continuum damage material model is constructed for brick and mortar separately. The degradation of both the stiffness and strength are governed by a damage variable. By using the proposed material model, damage and fragmentation of a typical masonry wall under blast loading at different scaled distances is calculated. The hazard level of the masonry wall to blast loading is evaluated by analyzing the numerical results. 相似文献
5.
ZHOU Xiaoqing HAO Hong DEEKS Andrew 《天津大学学报(英文版)》2006,12(B09):132-137
To model the damage process of masonry walls under blast loading, a dynamic continuum damage material model is constructed for brick and mortar separately. The degradation of both the stiffness and strength are governed by a damage variable. By using the proposed material model, damage and fragmentation of a typical masonry wall under blast loading at different scaled distances is calculated. The hazard level of the masonry wall to blast loading is evaluated by analyzing the numerical results. 相似文献
6.
Current practice in analysis and design of blast doors subjected to blast loading considers only simple boundary conditions and material properties. The boundary conditions and material properties, in fact, have considerable influence on the response of blast doors subjected to blast loading. In this paper, the dynamic responses of a reinforced concrete arched blast door under blast loading were analyzed by the finite element program ABAQUS, combined with a previously developed elasto-viscoplastic rate-sensitive material model. And the effect of the surrounding rock mass and contact effect of the doorframe were also taken into account in the simulation. It is demonstrated that the strain-rate effect has considerable influence on the response of reinforced concrete blast door subjected to blast loading and must be taken into account in the analysis. 相似文献
7.
Under extreme loading condition,a shelter will provide a safe place to protect people from injury caused by blast wave and fragments.In order to save resource and reuse waste materi-als,a new design concept for blast protection shelter was explored.The new construction was composed of I-section steel panel or C-channel steel panel filled with recycled concrete aggregate.The compaction process of the recycled concrete aggregate filled in the steel construction was ex-perimentally investigated.A single storey shelter based on the proposed design concept was nu-merically simulated by using LS-DYNA software.In the 3D numerical model,three walls were de-signed using I-section steel and one wall using C-channel steel,and all of the four walls were filled with recycled concrete aggregate.The penetration analysis was done by using ConWep.Some penetration tests were also carried out by using a gas gun.It is found that the proposed shelter based on the design concept is effective for blast protection. 相似文献
8.
研究目的：预测保护层开裂的时间以及分析锈胀参数
研究方法：基于混凝十的各向异性损伤,建立考虑钢筋腐蚀产物混凝十三者不同力学性能的钢筋锈胀导致保护层开裂的数学模型。模型考虑了腐蚀产物对钢筋混凝土界面区的孔隙和混凝十开裂裂缝的填充效应,采用了非线性分析算法,预测了开裂过程中每一时刻混凝土构件的应变与位移场以及混凝土保护层开裂时间,最后将模型预测值与试验值进行对比。
1.当混凝土出现裂缝之后,随着腐蚀产物对裂缝的填充,混凝土的环向拉应变的增长速率减缓;2.选定钢筋的型号、直径以及混凝土的强度之后,可通过增大保护层的厚度来减小钢筋锈胀开裂的风险。 相似文献
9.
HAO Qing-duo WANG Yan-lei ZHANG Zhi-chun OU Jin-ping 《浙江大学学报(A卷英文版)》2007,8(9):1356-1365
Based on the Canadian Standards Association (CSA) criteria,105 pullout specimens were tested to investigate the effect of different rib geometries on bond strength of glass fiber reinforced polymer (GFRP) rebars embedded in concrete. Two kinds of conventional reinforcing rebars were also studied for comparison. Each rebar was embedded in a 150 mm concrete cube,with the embedded length being four times the rebar diameter. The experimental parameters were the rebar type,rebar component,rebar diameter,rebar surface texture,rib height,rib spacing and rib width. Theoretical analysis was also carried out to explain the experimental phenomena and results. The experimental and theoretical results indicated that the bond strength of GFRP rebars was about 13%～35% lower than that of steel rebars. The bond strength and bond-slip behavior of the specially machined rebars varied with the rebar type,rebar diameter,rebar surface texture,rib height,rib spacing and rib width. Using the results,design recom-mendations were made concerning optimum rib geometries of GFRP ribbed rebars with superior bond-slip characteristics,which concluded that the optimal rib spacing of ribbed rebars is the same as the rebar diameter,and that the optimal rib height is 6% of the rebar diameter. 相似文献
10.
In the present paper, a dynamic plastic damage model for concrete has been employed to estimate responses of a reinforced concrete slab subjected to blast loading. The interaction between the blast wave and the concrete slab is considered in 3D simulation. In the first stage, the initial detonation and blast wave propagation is modelled in 2D simulation before the blast wave reaches the concrete slab, then the results obtained from 2D calculation are remapped to a 3D model. The calculated blast load is compared with that obtained from TM5-1300. Numerical results of the concrete slab response are compared with the explosive test carried out- in the Weapons System Division, Defence Science and Technology Organisation, Department of Defence, Australia. 相似文献
11.
ZHOU Xiaoqing HAO Hong KUZNETSOV Valerian A WASCHL John 《天津大学学报(英文版)》2006,12(B09):94-99
In the present paper, a dynamic plastic damage model for concrete has been employed to estimate responses of a reinforced concrete slab subjected to blast loading. The interaction between the blast wave and the concrete slab is considered in 3D simulation. In the first stage, the initial detonation and blast wave propagation is modelled in 2D simulation before the blast wave reaches the concrete slab, then the results obtained from 2D calculation are remapped to a 3D model. The calculated blast load is compared with that obtained from TM5-1300. Numerical results of the concrete slab response are compared with the explosive test carried out-in the Weapons System Division, Defence Science and Technology Organisation, Department of Defence, Australia. 相似文献
12.
LI Xiudi ZHENG Yingren 《天津大学学报(英文版)》2006,12(B09):177-181
In order to define the loading on protective doors of an underground tunnel, the exact knowledge of the blast propagation through tunnels is needed. Thirty-three scale high-explosive tests are conducted to obtain in-tunnel blast pressure for detonations external, internal and at the tunnel entrance. The cross section of the concrete model tunnel is 0.67 m^2. Explosive charges of TNT, ranging in mass from 400 g to 4 600 g, are detonated at various positions along the central axis of the model tunnel. Blast gages are flush-installed in the interior surface of the tunnel to record side-on blast pressure as it propagates down the tunnel. The engineering empirical formulas for predicting blast peak pressure are evaluated, and are found to be reasonably accurate for in-tunnel pressure prediction. 相似文献
13.
In order to define the loading on protective doors of an underground tunnel, the exact knowledge of the blast propagation through tunnels is needed. Thirty-three scale high-explosive tests are conducted to obtain in-tunnel blast pressure for detonations external, internal and at the tunnel entrance. The cross section of the concrete model tunnel is 0.67 m2. Explosive charges of TNT, ranging in mass from 400 g to 4 600 g, are detonated at various positions along the central axis of the model tunnel. Blast gages are flush-installed in the interior surface of the tunnel to record side-on blast pressure as it propagates down the tunnel. The engineering empirical formulas for predicting blast peak pressure are evaluated, and are found to be reasonably accurate for in-tunnel pressure prediction. 相似文献
14.
The blast resistance of structures used in buildings needs to be investigated due to the increased threat of a terrorist attack. The damage done by Composition B or Powergel to steel fibre reinforced reactive powder concrete (SFRPC) panels and ordinary reinforced concrete (RC) panels of equivalent static flexural strength is compared. A 0.5 kg charge was detonated at a distance of 0.1 m from the 1.3 m×1.0 m×0. 1 m (thick) panels, which were simply supported and spaning 1.3m. Dynamic displacement measurements, high-speed video recording and visual examination of the panels for spall and breach were undertaken. The SFRPC panels withstood the bare charge blast better than the reinforced ordinary concrete panels. Neither type of panel was breached using a 0.5 kg charge. The RC panel exhibited more spalling when Composition B was used. Under successive Composition B loading conditions, the RC panel was breached. In comparison the SFRPC panel was not breached. Exposure to fragmenting charge loading conditions confirmed these performance differences between the SFRPC panel and the reinforced ordinary concrete panel. 相似文献
15.
Terrorist attacks using improvised explosive devices (lED) can result in unreinforced masonry (URM) wall collapse.Protecting URM wall from lED attack is very complicated.An effective solution to mitigate blast effects on URM wall is to retrofit URM walls with metallic foam sheets to absorb blast energy.However,mitigation of blast effects on metallic foam protected URM walls is currently in their infancy in the world.In this palaer,numerical models are used to simulate the performance of aluminum foam protected URM walls subjected to blast loads.A distinctive model,in which mortar and brick units of masonry are discritized individually,is used to model the performance of masonry and the contact between the masonry and steel face-sheet of aluminum foam is modelled using the interface element model.The aluminum foam is modelled by a nonlinear elastoplastic material model.The material models for masonry,aluminum foam and interface are then coded into a finite element program LS-DYNA3D to perform the numerical calculations of response and damage of aluminum foam protected URM walls under airblast loads.Discussion is made on the effectiveness of the aluminum foam protected system for URM wall against blast loads. 相似文献
16.
Terrorist attacks using improvised explosive devices (IED) can result in unreinforced ma-sonry (URM) wall collapse. Protecting URM wall from IED attack is very complicated. An effective solution to mitigate blast effects on URM wall is to retrofit URM walls with metallic foam sheets to absorb blast energy. However, mitigation of blast effects on metallic foam protected URM walls is currently in their infancy in the world. In this paper, numerical models are used to simulate the per-formance of aluminum foam protected URM walls subjected to blast loads. A distinctive model, in which mortar and brick units of masonry are discritized individually, is used to model the perform-ance of masonry and the contact between the masonry and steel face-sheet of aluminum foam is modelled using the interface element model. The aluminum foam is modelled by a nonlinear elas-toplastic material model. The material models for masonry, aluminum foam and interface are then coded into a finite element program LS-DYNA3D to perform the numerical calculations of response and damage of aluminum foam protected URM walls under airblast loads. Discussion is made on the effectiveness of the aluminum foam protected system for URM wall against blast loads. 相似文献
17.
张萍 《廊坊师范学院学报(自然科学版)》2014,(3):66-68
针对混凝土结构中钢筋的锈蚀问题,总结了锈蚀钢筋力学性能的研究方法、锈蚀对钢筋力学性能的影响及锈蚀钢筋力学性能的变化规律等研究现状,提出了有待继续研究的问题,为进一步建立锈蚀钢筋模型和加强锈蚀钢筋防护奠定基础. 相似文献
18.
Spallation mechanism of RC slabs under contact detonation 总被引：2，自引：0，他引：2
The spallation of the concrete slabs or walls resulting from contact detonation constitutes risk to the personnel and equipment inside the structures because of the high speed concrete fragments even though the overall structures or structural members are not destroyed completely.Correctly predicting the damage caused by any potential contact detonation can lead to better for-tification design to withstand the blast loadings.It is therefore of great significance to study the mechanism involved in the spallation of concrete slabs and walls.Existing studies on this topic of-ten employ simplified material models and 1D wave analysis,which cannot reproduce the realistic response in the spallation process.Numerical simulations are therefore carried out under different contact blast loadings in the free air using LS-DYNA.Sophisticated concrete and reinforcing bar material models are adopted,taking into account the strain rate effect on both tension and com-pression.The erosion technique is used to model the fracture and failure of materials under tensile stress.Full processes of the deformation and dynamic damage of reinforced concrete (RC) slabs and plain concrete slabs are thus observed realistically.It is noted that with the increase of quantity of explosive,the dimensions of damage crater increase and the slabs experience four different damage patterns,namely explosive crater,spalling,perforation,and punching.Comparison be-tween the simulation results of plain concrete slabs and those of RC slabs show that reinforcing bars can enhance the integrity and shearing resistance of the slabs to a certain extent,and mean-while attenuate the ejection velocity and decrease the size of the concrete fragments.Therefore,optimizing reinforcement arrangement can improve the anti-spallation capability of the slabs and walls to a certain extent. 相似文献
19.
采用有限元软件AutoDyn,对TNT炸药起爆后爆炸冲击波遇到挡墙时的传播规律进行了三维数值模拟,分析了冲击波遇到挡墙时的反射高压及冲击波的环流汇聚作用。结果表明：冲击波遇到挡墙时将会产生反射高压;在比距离较小时,挡墙迎爆面的最大压力发生在挡墙底部;而随着比距离的增大,压力分布将沿挡墙高度趋于均匀。由于反射的作用,在挡墙前的地面上将会出现高压;当冲击波绕过挡墙时,在冲击波三个方向的绕射汇聚作用下,将会在墙后面一定区域内突然产生局部高压,并且随着传播的继续,这个区域不断的扩大,最后再次形成球面波传播。 相似文献
20.
Two numerical simulations were performed to investigate the protective effect of the foam cladding. One simulation is based on a previous experimental study, which is a ballistic pendulum with and without a foam cladding subjected to close-range blast loading. The other model is a steel beam with and without a foam cladding under blast loading. The overpressure due to the blast event can be calculated by the empirical function ConWep or by an arbitrary Lagrangian-Eulerian (ALE) coupling model. The first approach is relatively simple and widely used. The second approach can model the propagation of the blast wave in the air and the interaction between the air and the solid. It is found that the pendulum with the foam cladding always swings to a larger rotation angel compared to a bare pendulum. However, the steel beam with an appropriate foam cladding has a smaller deflection compared to the bare beam without a foam cladding. It is concluded that the protective effect of the foam cladding depends on the properties of the foam and the protected structure. 相似文献